Wellcraft 270 Coastal Скачать руководство пользователя страница 32

Страница: 32 / 121

Recommended procedure for making a shore

connection

Turn the AC main breakers to the “OFF” position. If

dockside outlet includes a disconnect switch or circuit

breaker, turn it to the “OFF” position also.

To avoid strain on the cables make sure they have more

slack than the mooring lines. Dress the cables so they

cannot be damaged by chafing between the boat and

the dock. Make sure the cables don’t come in contact
with the water. Then connect the cables in the boat plug

inlets and then the dockside outlets, making sure the

connection plugs include a three-prong plug with a

ground wire. Tighten the lock rings on the both the

shore and the boat connector plugs.

Turn the dockside disconnect switch or circuit breakers

to the “ON” position. If reverse polarity has been

achieved, the red polarity indictor in the 120-volt panel

will light. If this should happen, make sure the main

breakers on the AC panel are in the “OFF” position and

turn dock power switch or breaker off. Special relays
attached to the main breakers in the cabin AC panel will

automatically turn the main breakers off whenever

reverse polarity is achieved. Notify a qualified electrician

to check the wiring at the dock outlet. If the red polarity

light does not illuminate when the power is supplied to

the panel, the polarity is correct and the AC main
switches can be moved to the “ON” position.

Your boat is equipped with two 30 amp power cords that

activate shore circuit # 1 and shore circuit # 2. A

transfer main switch enables power from shore circuit #

1 or the generator to be directed to accessories on shore
circuit # 2 when two 30 amp shore power supplies are

not available or when operating on the generator. The

procedure to connect to shore power is the same for

both circuits.

Disconnecting procedure for shore power

connection

Turn the main breakers on the cabin AC panel off. Then

turn the disconnect switch or breaker on the dockside

outlets to the “OFF” position.

Disconnect the cables from the dockside outlet and

replace the outlet caps. Disconnect the cables from the

boat and close the inlet caps. Store cables.

Содержание 270 Coastal


























































































































Результаты поиска

Содержание 270 Coastal

Отзывы:

Wellcraft 270 Coastal, Руководство пользователя, Страница: 32 / 121

Результаты поиска

Содержание 270 Coastal

Отзывы: