Welker LS-14 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 33

background image

23

IOM-131

MODEL: LS-14

REV: F

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Disassembling the LS-14

Figure 13: LS-14 Maintenance Diagram

6.

Disconnect the tubing from the top cap.

7.

Disconnect the tubing between the inert gas supply tank and the pre-charge end cap.

8.

Remove the actuator cylinder hex nuts from the actuator cylinder tie bolts, and then remove the top cap.

9.

Remove the tracker tube and tracker magnet, and then set them aside. Take care not to misplace the tracker tube pins

inside the tracker tube.

10.

Slowly slide the actuator cylinder up and off the actuator piston.

11.

Remove the magnet retainer, magnet, and actuator piston from the mixer shaft (

12.

Loosen the receiver cylinder hex nuts on the pre-charge end cap, and then loosen the receiver cylinder hex nuts on the

product end cap.

13.

Fully unscrew six (6) of the receiver cylinder hex nuts on the pre-charge end cap and their respective receiver cylinder

hex nuts on the product end cap.

14.

Remove the six (6) receiver cylinder tie bolts by pulling them up and out of the pre-charge end cap.

15.

Fully unscrew and remove the remaining receiver cylinder hex nuts on the pre-charge end cap.

16.

Remove the pre-charge end cap from the LS-14.

17.

Carefully lift the pre-charge end cap straight up and off the mixer shaft.

«
...
21
22
23
24
25
...
»

Содержание LS-14


































Отзывы:

Нет отзывов

Похожие инструкции для LS-14

Бренд: NARGESA Страницы: 33

Бренд: Omnia Страницы: 8

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: JB-Lighting Страницы: 60

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды