Weinzierl 5256 Скачать руководство пользователя страница 4

Страница: 4 / 49

Page 4/49

2.1 KNX programming mode

The KNX programming mode is activated/deactivated either by pressing the flushed KNX
programming button

❸

or by simultaneously pressing the buttons

❼

and

❽

. The operation of

the programming mode at the front can be activated/deactivated in the ETS® with Prog. mode on
device front.

When the programming mode is active, the programming LED

❷

and the LED Mode

❺

light up

red.

2.2 Manual operation and status display

The LED KNX

❹

lights up or flashes when KNX bus voltage is present.

The LED Mode

❺

lights up or flashes when KNX bus voltage is present.

The LED RTU

❻

lights up or flashes when supply voltage is present.

The synchronization of the KNX objects is triggered by pressing the button KNX

❼

for a long time.

This is indicated by the LED Mode

❺

lighting up in orange.

Pressing the button RTU

❽

for a long time triggers the synchronization of the Modbus registers.

This is indicated by the LED Mode

❺

lighting up in orange.

The LED KNX

❹

is used to indicate the status of KNX communication. It flashes when sending

and receiving telegrams.

The LED RTU

❻

indicates the status of the Modbus communication. It flashes when sending and

receiving telegrams.

Summary of the states of the LED Mode

❺

LED Status

Meaning

LED lights green

The unit operates in normal operating mode.

LED lights red

The programming mode is active.

LED lights orange

The programming mode is not active.
Synchronization is active.

LED flashes red

The programming mode is not active.
Synchronization is not active.
The device is not loaded correctly, e.g. after aborting a download.

LED flashes green

The device is currently loaded by the ETS.

Содержание 5256


















































Результаты поиска

Содержание 5256

Отзывы:

Похожие инструкции для 5256

Бренды по названию

Популярные бренды

Weinzierl 5256, Руководство по эксплуатации и установке

Результаты поиска

Содержание 5256

Отзывы:

Похожие инструкции для 5256

Бренды по названию

Популярные бренды