Weinzierl 5256 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 49

background image

© 2020 Weinzierl Engineering GmbH

Page 34/49

Position (register)

This parameter defines the area of the word register which is read/written. The following areas are
available:

▪

Low byte

▪

High byte

▪

Configured

Offset (only for configured)

This parameter defines the position of the area in the word register (offset from the right in bits).

5.11

Channel function “DPT 07 – configured – 2 bytes”

Type

The following types are configurable:

▪

Bit register

2 byte value configured (KNX) sets bit register (Modbus)

▪

Bit in word register

2 byte value configured (KNX) sets 1 bit in word register (Modbus)

▪

Value in word register

2 byte value configured (KNX) is mapped to value in word register (Modbus)

5.11.1 Type

– Bit register

5.11.1.1 Direction

– KNX to Modbus

Value (object)

This parameter defines the value for which the group object (KNX) is checked.

«
...
32
33
34
35
36
...
»

Содержание 5256


















































Отзывы:

Нет отзывов

Похожие инструкции для 5256

Бренд: CloudGate Страницы: 25

Бренд: CTC Union Страницы: 4

Бренд: TDL Страницы: 47

Бренд: Hirschmann Страницы: 44

WPC-832-2-Modbus-MQTT

Бренд: KSH International Страницы: 16

Бренд: Technicolor Страницы: 19

Бренд: SAE Страницы: 17

Бренд: Hitron Страницы: 128

Бренд: Four-Faith Страницы: 32

Бренд: ZyXEL Communications Страницы: 35

Бренд: Daikin Страницы: 8

Бренд: Celestix Страницы: 37

Бренд: ViewSonic Страницы: 48

Бренд: 2N Страницы: 9

Бренд: 2N Страницы: 57

Бренд: 2N Страницы: 67

Бренд: GE Security Страницы: 6

OfficeConnect 3C100XF

Бренд: 3Com Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды