Weinzierl 5256 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 49

background image

© 2020 Weinzierl Engineering GmbH

Page 40/49

Behaviour on value lower

This parameter defines the behaviour of the word register in case the received value (KNX) is
smaller than the parameterized value. The following options are available:

▪

No reaction

▪

Set value in register

Value (register)

The value that is set in the word register.

5.11.3.2 Direction

– Modbus to KNX

Value (register)

This parameter defines the value for which the word register is checked.

Behaviour on value higher

This parameter defines the behaviour of the group object (KNX) in the event that the register value
is greater than the parameterized value. The following options are available:

▪

No reaction

▪

Send value

Value (object)

The value that is sent via the group object (KNX).

«
...
38
39
40
41
42
...
»

Содержание 5256


















































Отзывы:

Нет отзывов

Похожие инструкции для 5256

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 66

Бренд: IFM Electronic Страницы: 9

SymbiLink SLN-4

Бренд: zapco Страницы: 15

iO-GridM GFGW-RM02N

Бренд: DAUDIN Страницы: 28

Бренд: THOMSON Страницы: 710

Mediant 500Li MSBR

Бренд: AudioCodes Страницы: 10

Бренд: PTT Страницы: 21

Бренд: Garmin Страницы: 8

Бренд: SpectraLink Страницы: 15

ThingPark Partner

Бренд: Actility Страницы: 4

Бренд: CALEFFI Страницы: 20

Бренд: Next Level Security Systems Страницы: 10

Бренд: Intermatic Страницы: 6

Бренд: Entone Страницы: 19

Hydra HD - B Serie

Бренд: Entone Страницы: 49

Бренд: DBL Technology Страницы: 69

ecomat 300 AC1155

Бренд: IFM Electronic Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды