Weidmüller maxGUARD Скачать руководство пользователя страница 53

Страница: 53 / 78

9 Operation

WARNING

Explosion risk!

▶

Before starting any work, make sure that

there is not a potentially explosive atmos-

phere!

ATTENTION

The product can be destroyed!

▶

Before each commissioning, carry out an insulation test

of the station.

ATTENTION

The product can be destroyed!

▶

Make sure that the output voltage is not higher than the

input voltage on a permanent basis.

9.1 Commissioning

Before you start the commissioning work, the following re-

quirements must be fulfilled:

–

The maxGUARD station must be fully assembled and

wired.

–

The adjustable load monitors must be correctly configured.

–

The power supply must be connected.

–

The maxGUARD station must be connected to a control

unit if necessary.

▶

Switch on the power supply.

The electronic load monitors save their operation-

al state. After the power supply is switched back

on, the load monitor automatically switches to its

last operational state before powering down.
The electronic load monitors are switched off ex

works. When first commissioned, the load moni

tors must therefore be switched on individually.

▶

Switch on all load monitors individually by pressing the

respective reset button “R”.

9.2

Switching load monitors on/off

To avoid unexpected operational states, individu-

ally switched off load monitors ignore the reset

and ON/OFF signals on the internal signal line.

Individually switched off load monitors can only

be switched on individually.

Switching load monitors on/off individually

▶

While switched off, press the reset button “R” for 0.1 to 2

seconds.

The load monitor will switch to ready state and the LED will

illuminate green.

▶

While in ready state, press the reset button “R” for 0.1 to

2 seconds.

The load monitor will switch off and the LED will illuminate

red.

Manually switching a segment on/off

You can switch on/off all load monitors in a segment using

the reset button “R” on an AMG CM control module. All load

monitors in the segment must be connected to the control

module via the internal signal line.

▶

Press the reset button “R” on the control module for 0.1

to 2 seconds to couple the ON/OFF signal into the inter-

nal signal line.

All ready and tripped load monitors in the segment will

switch off and the LEDs will illuminate red.

Switching a segment on/off with a control unit

You can switch off all load monitors in a segment using the

ON/OFF signal of an AMG CM control module. All load moni

tors in the segment must be connected to the control mod-

ule via the internal signal line.

▶

To switch off all load monitors in the segment, set the

ON/OFF input of the control module to +24 V for longer

than 100 ms.

The ON/OFF LED on the control module will illuminate yel-

low. All load monitors will switch off. The LEDs on the load

monitors will illuminate red. The load monitors will remain

switched off by permanently setting the level to 24 V.

▶

To switch all load monitors in a segment back on, set the

ON/OFF input of the control module to 0 V.

The ON/OFF LED on the control module will switch off. All

load monitors will switch to ready state. The LEDs on the

load monitors will illuminate green.

Manual maxGUARD

2526740000/02/03.2018

9 Operation

| Commissioning

Содержание maxGUARD















































































Результаты поиска

Содержание maxGUARD

Отзывы:

Бренды по названию

Популярные бренды

Weidmüller maxGUARD, Руководство пользователя

Результаты поиска

Содержание maxGUARD

Отзывы:

Бренды по названию

Популярные бренды