background image

metal
spring

DIN-Rail

   

metal
spring

DIN-Rail

   

To remove the Media Converter from the DIN-Rail, simply reverse 
Steps 1 and 2 above. 

Wall Mounting (Optional) 

For some applications, you will find it convenient to mount the Media 
Converter on the wall, as illustrated below. 

STEP 1

Remove the aluminum DIN-Rail attachment plate from the device, 
and then attach the wall mount plates, as shown in the diagrams 
below. 

 

STEP 2

: Mounting the Media Converter on the wall 

requires 4 screws. Use the Media Converter, with 
wall mount plates attached, as a guide to mark the 
correct locations of the 4 screws. The heads of the 
screws should be less than 6.0 mm in diameter, and 
the shafts should be less than 3.5 mm in diameter, as 
shown in the figure at the right. 

NOTE

  Test the screw head and shank size by 

inserting the screw into one of the keyhole 
shaped apertures of the Wall Mounting 
Plates, before it is screwed into the wall. 

Do not screw the screws in all the way—leave a 
space of about 2 mm to allow room for sliding the wall 
mount panel between the wall and the screws.

 

6.0 mm

3.5 mm

STEP 3

: Once the screws are fixed in the wall, insert the four screw 

heads through the large parts of the keyhole-shaped apertures, and 
then slide the Media Converter downwards, as indicated below. 
Tighten the four screws for added stability. 

 

- 5 -

Содержание IE-MC-VL















Отзывы: