background image

Dip Switch Setting 

IE-MC-VL Series DIP switch

 

1 2 3

ON      DIP

 

Dip Switch 1 (Default: Off ) 

ON

: Enables the PORT Alarm. If the port’s link fails, 

the relay will form an open circuit and the fault 
LED will light up. 

Off

: Disables the corresponding PORT Alarm. The 

relay will form a closed circuit and the Fault 
LED will never light up. 

Dip Switch 2 (Default: ON ) 

ON

: Enables full duplex for 100BaseFX 

Off

: Disables full duplex for 100BaseFX 

Dip Switch 3

 

Reserved for future use 

To activate the updated DIP switch settings, power off and then 
power on the Media Converter. 

 

LED Indicators 

The front panel of the Media Converter contains several LED 
indicators. The function of each LED is described in the table below. 

LED 

Color 

State 

Description 

On 

Power is being supplied to 

power input PWR1 

PWR1 

AMBER 

Off 

Power is 

not

 being supplied 

to power input PWR1 

On 

Power is being supplied to 

power input PWR2 

PWR2 

AMBER 

Off 

Power is 

not

 being supplied 

to power input PWR2 

On 

When the corresponding 

PORT alarm is enabled, 

and the port’s link is 

inactive. 

FAULT 

RED 

Off 

When the corresponding 

PORT alarm is enabled and 

the port’s link is active, or 

when the corresponding 

PORT alarm is disabled. 

On 

TP port’s 10 Mbps link is 

active 

Blinking 

Data is being transmitted at 

10 Mbps 

10M 

GREEN 

Off 

TP Port’s 10 Mbps link is 

inactive 

100M 

GREEN 

On 

TP port’s 100 Mbps link is 

active 

 

- 11 -

Содержание IE-MC-VL















Отзывы: