24. Route the Long Cable (45) under a 3 1/2” Pulley
(12). Attach the Pulley and two Pulley Covers (13)
to the “U” bracket on the Stabilizer (69) with the
3/8” x 2” Bolt (38) and a 3/8” Jam Nut (2). Make
sure that the Pulley Covers are turned so the
wide tabs are positioned as shown.
25. Feed the Long Cable (45) under the Weights (46).
Refer to the CABLE DIAGRAM on page 23 to
see how the Cable should be routed.
Route the Long Cable (45) under a 3 1/2” Pulley
(12). Attach the Pulley and two Pulley Covers (13)
to the bracket on the Base (43) with a 3/8” x 1 3/4”
Bolt (14) and a 3/8” Jam Nut (2). Make sure that
the Pulley Covers are turned so the wide tabs
are positioned as shown.
Feed the Long Cable (45) over the lower 4 1/2”
Pulley (85).
26. Route the Long Cable (45) under a 3 1/2” Pulley
(12). Attach the Pulley and two Pulley Covers (13)
to the indicated side of the Frame (80) with the
3/8” x 4” Bolt (64) and a 3/8” Nylon Locknut (27).
Make sure that the Pulley Covers are turned
so the wide tabs are positioned as shown.
27. Route the Long Cable (45) up around a 3 1/2”
Pulley (12). Attach the Pulley and two Pulley
Covers (13) to the indicated side of the Press
Arm (28) with a 3/8” x 3 1/4” Bolt (5) and a 3/8”
Jam Nut (2). Make sure that the Pulley Covers
are turned so the wide tabs are positioned as
shown.
24
27
26
25
13
45
27
13
13
2
46
14
85
2
69
45
12
Wide Tab
13
13
38
45
13
Wide Tab
Wide Tab
Wide Tab
43
12
13
64
45
12
80
2
13
12
Wide Tab
28
5
12
28. Route the Long Cable (45) around the 3 1/2” “V”-
Pulley (10). Attach the “V”-Pulley to the bracket
on the Frame (80) with a 3/8” x 2 1/2” Bolt (3) and
a 3/8” Nylon Locknut (27).
29. Route the Long Cable (45) down around a 3 1/2”
Pulley (12). Attach the Pulley and two Pulley
Covers (13) to the indicated side of the Press
Arm (28) with a 3/8” x 3 1/4” Bolt (5) and a 3/8”
Jam Nut (2). Make sure that the Pulley Covers
are turned so the wide tabs are positioned as
shown.
30. Remove the indicated 3/8” Nylon Locknut (27).
Do not remove the 3/8” x 4” Bolt (64).
Attach the end of the Long Cable (45) to the 3/8”
x 4” Bolt (64) with the 3/8” Nylon Locknut (27). Do
not overtighten the Nylon Locknut; the Cable
must pivot freely.
IMPORTANT: Before continuing, refer to
TROUBLE-SHOOTING AND MAINTENANCE on
page 21, and adjust the cables as described.
31. Tap a 1 3/4” x 1 3/4” Inner Cap (24) into each of
the VKR Arms (73, 74). Tap a 1” Round Cap (22)
into the handle on each VKR Arm.
Attach the Left and Right VKR Arms (73, 74) to
the VKR Upright (70) with two 3/8” x 2 3/4” Bolts
(81) and two 3/8” Jam Nuts (2).
31
30
29
28
10
3
45
13
2
12
13
Wide Tab
45
28
5
27
45
64
80
81
24
73
22
22
2
74
24
70
27
80
13
