Main Frame
Seat Assembly (773-A)
Console (714)
Console Mast Assembly
Console Mast Cover
Mounting Plates (315)
Console Mast Covers (316)
Front Stabilizer (711-A)
Rear Leg Assembly (710-A)
Beam End Cap (707)
T-Handle Assembly (789-A)
Beam Assembly
Console Pivot Covers (716)
T-Handle Holder
Assembly (737-A)
Foot Platform - Left (732-A)
Foot Platform - Right (733-A)
*NOTE: CHAIN IS INSTALLED FROM BEAM ASSEMBLY TO MAIN FRAME; MAKE NOTE DURING ASSEMBLY
ASSEMBLY TOOLS
3mm
Hex Wrench
(806)
4mm
Hex Wrench
(807)
5mm
Hex Wrench
(808)
6mm
Hex Wrench
(809)
Spring Washer
Ø13.3OD x Ø8.2ID x 1.8t (703)
Button Head Hex Screw
M8 x 1.25 x 12mm (704)
Round Head Cross Tapping Screw
M3.5 x 10mm Long (709)
Socket Head Hex Screw
M8 x 1.25 x 16mm (304)
HARDWARE DESCRIPTION
DRAWING QUANTITY
Flat Washer
Ø19.0OD x Ø8.5ID x 1.2t (305)
Button Head Hex Screw
M5 x 0.8 x 10mm (708)
Socket Head Hex Screw
M8 x 1.25 x 25mm (317)
Socket Head Hex Screw
M3 x 0.5 x 8mm (319)
20
8
2
2
2
20
8
4
2.5mm
Hex Wrench
(805)
Socket Head Hex Screw
M8 x 1.25 x 40mm (712)
Button Head Hex Screw
M5 x 0.8 x 20mm Long (738)
Socket Head Hex Screw
M5 x 0.8 x 12mm (715)
6
10
4
11mm Wrench
Assembly Step 1: Front Stabilizer Installation
• Install the
Front Stabilizer (711-A)
by placing one
M8 Flat Washer
(305)
and one
M8 Spring Washer (703)
onto each of the
M8 x 1.25
x 16mm Socket Head Hex Screws (304)
. Loosely thread the screws
through the underside of the
Front Stabilizer (711-A)
and into the
Main Frame
. Secure the screws in place with the
6mm Hex Wrench
(809)
.
Assembly Step 3: Rear Leg Assembly Installation
• Install the
Rear Leg Assembly (710-A)
by placing one
M8 Flat Washer
(305)
and one
M8 Spring Washer (703)
onto each of the
M8 x 1.25 x
25mm Socket Head Hex Screws (317)
. Loosely thread the screws through
the underside of the
Rear Leg Assembly (710-A)
and into the
Beam
Assembly
. Secure the screws in place with the
6mm Hex Wrench (809)
.
ASSEMBLY
Introduction
• The Assault Fitness AirRower Elite requires assembly prior to use. Tools required to complete the initial setup and assembly have
been included in the Assembly Hardware Kit.
• Lift box top off of contents. Remove all loose parts and the hardware kit from the side of the styrofoam carton. Set aside
styrofoam and remove styrofoam from top of frame but
leave the main frame assembly and beam assembly in the
styrofoam and proceed to Step 1 below
.
• Confirm all parts shown in the section above titled
As Shipped
are included before attempting assembly of the AirRower Elite.
Assembly Step 5: Console Mast and Console Installation
• The
Computer Mast Cable (810)
is pre-installed and should be extending
from the top to the bottom of the
Console Mast Assembly
. Connect the
top end of the
Computer Mast Cable (810)
extending from the
Console
Mast Assembly Pivot Bracket
into the cable extending from the hole in the
backside of the console and carefully tuck the excess cable into the
Console
(714)
.
• Align the mounting holes located in the back of the
Console (714)
with the
holes in the
Console Mast Assembly Pivot Bracket
and loosely thread in the
four
M5 x 0.8 x 12mm Socket Head Hex Screws (715)
. Tighten using the
4mm Hex Wrench (807)
.
• Next, install the
Console Pivot Covers (716)
using the six
M5 x 0.8 x 12mm
Socket Head Hex Screws (715)
and tighten using the
4mm Hex Wrench
(807)
.
Assembly Step 9: Leveling the Unit
• Select a suitable space for operation of the AirRower Elite. Move the unit to the desired location by raising the rear stabilizer
off the ground until the transport wheels touch the ground. Slowly push the unit into place. Ensure there is at least 0.5 m
(19.7 in.) of clearance on all sides of the rower.
• Ensure the unit is level and does not rock by adjusting the
Leveling Feet
. There are two feet on the Front Stabilizer and two
on the Rear Stabilizer. As a starting point, loosen each foot by turning the leveler clockwise (when looking down towards
the leveler), and then loosen the locknuts against the foot base. Check the unit for stability and make any adjustments as
necessary. Once stable, lock the
Leveling Feet
in place by tightening the jam nut, against the underside of the stabilizer to
lock the current position of each foot.
• Congratulations, your new Assault AirRower Elite is fully assembled and ready for use. Please read all included information,
user guides and warnings before use.
Part #23-AS-799 US-English v1.0 03-April-19
QUICK START
GUIDE
www.assaultfitness.com
© Assault Fitness 2019
Assembly Step 2: Beam Installation
• With the assistance of a second person, rotate the
Main Frame
and supporting styrofoam as shown in the figure until they rest
on the floor.
NOTE: Be careful and keep the chain in line with the beam as the frame is rotated towards the floor in order
to ensure that the chain does not get kinked or bent.
• Cut the zip tie holding the chain to the lower box, but before doing so, note the warning below:
WARNING: There is tension in the chain which will pull the Beam Assembly towards the Main Frame once
the zip tie is cut.
711-A
703
305
304
• Align the
Beam Assembly
with the
Main Frame
and slide the beam onto the beam fixing joint as shown.
• Secure the
Beam Assembly
by placing one
M8 Flat Washer (305)
and one
M8 Spring Washer (703)
onto each of the
M8
x 1.25 x 12mm Button Head Hex Screws (704)
. Loosely thread the screws through the
Beam Assembly
side wall and and
into the
Main Frame
. Secure the screws in place with the
6mm Hex Wrench (809)
.
704
703
305
704
703
305
305
703
317
710-A
Assembly Step 4: Foot Platform Installation
• Install the
Foot Platforms (732-A and 733-A)
by placing
one
M8 Flat Washer (305)
and one
M8 Spring Washer
(703)
onto each of the
M8 x 1.25 x 40mm Socket Head Hex
Screws (712)
. Loosely thread the screws through the inside of
each
Foot Platforms (732-A and 733-A)
and into the
Beam
Assembly
. Secure the screws in place with the
6mm Hex
Wrench (809)
.
712
703
305
733-A
712
703
305
732-A
810
716
715
715
714
716
715
317
315
802-A
810
319
316
316
319
• Connect the lower end of the
Computer Mast Cable (810)
extending from the
Console Mast Assembly
into the
RPM
Sensor and Cable Assembly (802-A)
extending from the
Main Frame
and carefully tuck the excess cable into the
Main
Frame
or
Console Mast Assembly
.
• Align the mounting plate for the
Console Mast (312)
with the mounting holes in the
Main Frame
. Loosely thread two
M8
x 1.25 x 25mm Cap Head Hex Screws (317)
through each
Console Mast Cover Mounting Plate (315)
and
Console Mast
Assembly
and into the
Main Frame
. Tighten all screws firmly using the
6mm Hex Wrench (809)
.
• Finally, install the two
Console Mast Covers (316)
using the four
M3 x 0.5 x 8mm Socket Head Hex Screws (319)
. and
tighten firmly using the
2.5mm Hex Wrench (805)
.
•
Assembly Step 6: Seat and End Cap Installation
• Slide the
Seat Assembly (773-A)
onto the
Beam Assembly
in the orientation shown. Do not force it on the Beam or you
could risk damaging the wheels.
• Install the
End Cap (707)
using the two
M5 x 0.8 x 10mm Button Head Hex Screws (708)
and tighten using the
3mm Hex
Wrench (806)
. Next install the two
M3.5 x 10mm Long Round Head Cross Tapping Screws (709)
through the underside of
the beam using a Phillips head screwdriver to complete the installation of the
End Cap (707)
.
707
708
773-A
709
737-A
738
Assembly Step 7: T-Handle Holder Installation
• Install the
T-Handle Holder Assembly (737-A)
using the four
M5 x 0.8 x 20mm
Button Head Hex Screws (738)
and tighten using the
3mm Hex Wrench (806)
.
Assembly Step 8: T-Handle Installation
• Pull the chain forward from the shroud opening
using the connected zip tie.
• Install the
T-Handle Assembly (789-A)
using
the
T-Handle U-Bolt (767)
,
two 1/4-20 UNC
Nuts (717)
, and two
Ø10.0OD x Ø5.5 x 1t Flat
Washers (412)
and tighten using the provided
11mm Wrench
.
• Cut the zip tie from the chain.
• Place the
T-Handle Assembly (789-A)
in the
T-Handle Holder
.
767
412
717
789-A
