background image

Signals

5-4 | PSRW

5

 

„

Safety outputs (equal or reversed).

ATTENTION!

Auxiliary output is only to no safety functions.

5.5 TEST OUTPUTS

To monitor the digital inputs configured as contact, it is necessary to use the test outputs (TEST_A and TEST_B) 
generated by the PSRW. The PSRW has two test output channels that must be connected to their respective 
input channel (channel A to channel A/channel B to channel B) for the correct operation of the input.

The OUT TEST TEST_A and TEST_B signals must be used to monitor the presence of short-circuits or overloads 
on the inputs see 

Figure 5.4 on page 5-4

.

Emergency

20

19

4

3

17

18

Safety 

sensor

IN_2B

IN_2A

IN_1B

IN_1A

TEST_A

TEST_B

PSRW

Figure 5.4: 

Example of TEST_A and TEST_B connection

ATTENTION!

The maximum allowed length for test outputs connections is 30 meters.

ATTENTION!

Is not allowed connect the

 

test outputs to supply an external component.

5.6 OSSD OUTPUTS

The OSSD are short circuit protected, cross circuit monitored and supply:

 

„

In the ON condition: 

Uv - 1 V

 (where Uv is 24 V ± 20 %).

 

„

In the OFF condition: 

0 V / 2 V

rms

.

 

„

The maximum load of 

2A@24V

 corresponds to a minimum resistive load of 

12 Ω

.

¹

 Each OSSD channel can 

supply up to two (2) Amps. However, the sum of the currents of the four channels cannot exceed 2 (two) Amps.

 

„

The maximum capacitive load is 

1 uF

 

„

The maximum inductive load is 

30 mH

.

See 

Section 6.2 TECHNICAL SPECIFICATIONS on page 6-1

 for maximum current.

Содержание PSRW




























































Отзывы: