Weco HeSU 4k4 PRO Скачать руководство пользователя страница 46

Страница: 46 / 46

WeCo Srl Italia

www.wecobatteries.com

4K4 PRO V 1.11 28-9-2021

DO NOT

connect the 4K4PRO Battery module to an inverter which has no BMS-CAN interface without receiving prior approval from the

WeCo technical team. To obtain approval contact

[email protected]

and wait for a response BEFORE making any connection.

USING THE BATTERY OUTSIDE OF THE WORKING RANGE AS DEFINED IN THIS MANUAL WILL DAMAGE THE

BATTERY AND WILL VOID THE WARRANTY.

NOTE:

This manual is subjected to continuous implementation.

Before install your WeCo batteries please contact our assistance team in order to have the latest manual and any additional support.

Safety improvement is our priority, please cooperate with us to improve the system, any suggestion is well accepted.

WeCo Srl, Italia

Содержание HeSU 4k4 PRO















































Результаты поиска

Содержание HeSU 4k4 PRO

Отзывы:

Похожие инструкции для HeSU 4k4 PRO

Бренды по названию

Популярные бренды

Weco HeSU 4k4 PRO, Руководство по установке

Результаты поиска

Содержание HeSU 4k4 PRO

Отзывы:

Похожие инструкции для HeSU 4k4 PRO

Бренды по названию

Популярные бренды