Weco HeSU 4k4 PRO Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 46

background image

WeCo Srl Italia

www.wecobatteries.com

[email protected]

4K4 PRO V 1.11 28-9-2021

4 PRODUCT OVERVIEW

4.1 Product Introduction

The HeSU Series batteries can be used as an on-grid or off-grid energy storage system. It is recommended not to use this product for any
purpose other than the intended purpose as described in this document.

Use of this product other than as described in this document will nullify the product guarantee. The substitution or installation of any
components of this battery will nullify the product guarantee.

The use of any components contained within or connected to this battery other than the products sold as part of this product or
recommended by the manufacturer will nullify the product guarantee.

Connecting more than five individual HeSU 4K4 PRO battery units in parallel will nullify the product guarantee.

4.2 Identifying the Product Components

Front RUN BUTTON Version

BATTERY HANDLE (feet)

RUN/STOP Button 2

DIP SWITCH

RS 232 OPERATOR PORT

RS 485 PARALLEL A/B

BMS CAN

D/I-D/O

RS 232 / LAN connection

EARTHING POINT

NEGATIVE TERMINALS

POSITIVE TERMINALS

«
...
8
9
10
11
12
...
»

Содержание HeSU 4k4 PRO















































Отзывы:

Нет отзывов

Похожие инструкции для HeSU 4k4 PRO

Delta Ready Pro

Бренд: Hama Страницы: 4

Бренд: Chicago Electric Страницы: 10

Бренд: Elettro CF Страницы: 20

Abso Charger 12V 20A

Бренд: Kisae Страницы: 21

Certa CTMWR40CHAA

Бренд: Kogan Страницы: 12

Бренд: LEGRAND Страницы: 4

Бренд: Circutor Страницы: 26

Бренд: ENEL Страницы: 4

Бренд: R&S Страницы: 33

Linea Pro Pistol Grip Charging Station

Бренд: Infinite Peripherals Страницы: 2

Infinea Tab Lite

Бренд: Infinite Peripherals Страницы: 13

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 137

Бренд: ABB Страницы: 152

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 205

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды