WWW.WEbER.com
®
31
PRobLEm
cHEcK
SoLUTIoN
side burner does not light.
Is gas supply off?
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated .
Turn gas supply on .
To reset the excess flow safety device turn all burner
control knobs and the cylinder valve off . Disconnect the
regulator from the cylinder . Turn burner control knobs to
START/HI . Wait at least one minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to “SIDE BURNER
IGNITION” .
flame is low in hi position.
Is the fuel hose bent or kinked?
Straighten hose .
push button ignition does not work.
Does burner light with a match?
If match lights burner, check igniter . Refer to “SIDE
BURNER MAINTENANCE” .
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
®
.
PRobLEm
cHEcK
SoLUTIoN
burners burn with a yellow or orange flame, in
conjunction with the smell of gas. (this is normal for
the burner lighting tube.)
Inspect Spider/Insect screens for possible obstructions .
(Blockage of holes .)
Clean Spider/Insect screens . Refer to “ANNUAL
MAINTENANCE” .
symptoms:
burners do not light. -or- burners have a small
flickering flame in the hi position. -or-
barbecue temperature only reaches 250° to 300° in
the hi position.
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated .
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve off . Disconnect
the regulator from the cylinder . Turn burner control
knobs to HI . Wait at least 1 minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to “MAIN BURNER
IGNITION” .
burner does not light, or flame is low in hi position.
Is LP fuel low or empty?
Refill LP cylinder .
Is fuel hose bent or kinked?
Straighten fuel hose .
Does burner light with a match?
Clean burners . Refer to “MAINTENANCE” .
Did you use the snap igniter several times until the main
burner lit? Refer to “MAIN BURNER IGNITION” .
Make sure to hold the control knob in for two seconds
after snapping the igniter and seeing the orange flame
from the burner lighting tube .
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
Try manually lighting the burner . Refer to “MAIN
BURNER MANUAL IGNITION” . Call customer service .
experiencing flare-ups:
m
Caution: do not line the slide out
grease tray with aluminum foil.
Are you preheating barbecue in the prescribed manner?
All burners on HI for 10 to 15 minutes for preheating .
Are the cooking grates and Flavorizer
®
bars heavily
coated with burned-on grease?
Clean thoroughly . Refer to “CLEANING” .
Is the bottom tray “dirty” and not allowing grease to flow
into catch pan?
Clean bottom tray .
burner flame pattern is erratic. flame is low when
burner is on hi. flames do not run the whole length
of the burner tube.
Are burners clean?
Clean burners . Refer to “MAINTENANCE” .
inside of lid appears to be “peeling.” (resembles
paint peeling.)
The lid is porcelain enamel or stainless steel, not paint .
It cannot “peel” . What you are seeing is baked on grease
that has turned to carbon and is flaking off .
this is not a defeCt.
Clean thoroughly . Refer to “CLEANING” .
Cabinet doors are not aligned.
Check the adjustment pin on the bottom of each door.
Loosen adjustment nut/s. Slide door/s until aligned.
Tighten nut .
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
®
.
TRoUbLESHooTING
SIDE bURNER TRoUbLESHooTING
Содержание Summit 56211
Страница 109: ...www weber com 109 MEMO...
