background image

7

4. Safety

General

All safety instructions must be read and complied with, as non-

compliance will result in

 

-  Danger to life and limb of the user,

 

-  Impairments to the machine or other property.

In addition to the operating manual, the accident-prevention 

regulations in the country where the appliance is used must be 

complied with.

Intended use

The machine should only be used in technically faultless 

condition, as intended, in a safety-conscious and hazard-

conscious manner, and in compliance with the instructions in 

the operating manual. 

Malfunctions that may impair safety require that you stop 

working with the machine immediately. These types of damage 

must be reported and corrected without delay.  

The machine is designed exclusively for compacting:

 

- Sand,

 

- Gravel,

 

- Crushed rock,

 

- Semi-cohesive mixed material.

The operator's work position is behind the machine. The 

operator must guide the machine safely with both hands on the 

handle. 

Non-intended use

Unless used as intended, the machine involves a risk of 

personal injury and property damage. The machine is 

expressly not suitable for:

 

-  compacting frozen subsurfaces,

 

-  compacting hard soils that cannot be compacted 

further,

 

-  compacting non-bearing material,

 

-  compacting highly cohesive soils,

 

-  compacting (ramming) that exerts point loads on 

the base plate,

 

-  crushing and compacting individual rocks. 

The responsibility for any damage arising from non-intended 

use falls on the owner / operator rather than the manufacturer. 

Damage that can be attributed to non-intended use of the 

machine will void any warranty claims. 

Residual risk

There is always an increased risk of accidents in the 

immediate danger area around the machine if the operator 

fails to notice persons in the vicinity of the machine. 

Make anyone close to the machine aware of this risk. The 

operator must not put the machine into operation unless 

everyone in the vicinity of the machine is aware of this risk. 

Содержание 0170051





























Отзывы:

Похожие инструкции для 0170051