Wayne-Dalton IDrive 3651-372 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 42

background image

Tools Needed:

Tools Needed:

You can reach us Toll Free at

1-888-827-3667

for Consumer Assistance or online at

www.wayne-dalton.com

Please Do Not Return This Product To The Store.

Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need

17

Attaching Safety Sensors

Attach the Sending and Receiving Safety
Sensors to the “U” Brackets by inserting
all three tabs into the respective holes.

IMPORTANT!

Identify which side of the

garage door is exposed to the most
sunlight. Mount the Sending Unit (Unit
without LED) on the side which is exposed
to the most sun. Sunlight may affect the
Safety Sensors, this orientation will help
reduce the effect.

Receiving

Unit

LED

None

Routing Safety Sensor Wires

Uncoil Wires from Safety Sensors and
route Wires up garage wall and above
torsion tube towards the right side of the
Opener Power Head.

Route Wires behind torsion tube and tack
Wires in place with Insulated Staples.

NOTE:

If wires must be lengthened or

spliced use wire nuts or suitable
connectors.

18

Hammer

Wire Routing

9

«
...
14
15
16
17
18
...
»

Содержание IDrive 3651-372











































Отзывы:

Нет отзывов

Похожие инструкции для IDrive 3651-372

Controll-A-Door Secure SDO-6

Бренд: B&D Страницы: 2

CALYPSO 400 CA43

Бренд: Erreka Страницы: 46

Бренд: CAME Страницы: 14

3280M-267 1/2HP

Бренд: Chamberlain Страницы: 36

Бренд: Security + Страницы: 76

Бренд: RAMSET Страницы: 26

Бренд: GiBiDi Страницы: 16

Бренд: GarageAce Страницы: 20

Бренд: Garage Door Systems Страницы: 32

Бренд: Protectrix Страницы: 2

Бренд: CAME Страницы: 32

Бренд: tau Страницы: 13

Бренд: Wallace Perimeter Security Страницы: 142

Бренд: Daspi Страницы: 20

Бренд: idomus Страницы: 16

Бренд: OneTouch Страницы: 6

Бренд: CAME Страницы: 7

Бренд: CAME Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды