Wayne-Dalton IDrive 3651-372 Скачать руководство пользователя

Страница: 7 / 42

You can reach us Toll Free at

1-888-827-3667

for Consumer Assistance or online at

www.wayne-dalton.com

Please Do Not Return This Product To The Store

Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need

INCORRECT

INSTALLATION CAN LEAD TO

SEVERE OR FATAL INJURY.

FOLLOW THESE INSTRUCTIONS

CAREFULLY.

IMPORTANT SAFETY

INSTRUCTIONS

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2. Do not connect the Opener to electrical power until

instructed to do so.

3. Install the Entrapment Warning Label next to the

Wall Station in a prominent location. Install the Emergency

Disconnect Label next to the Emergency Disconnect.

4. Remove all ropes and remove or make inoperative in the

unlocked position, all locks connected to the garage door

before installing the Opener.

5. Do not wear rings, watches or loose clothing when installing

or servicing a garage door system.

6. It is important that you install all the components supplied

with the idrive Opener, i.e., Wall Stations, Safety Sensors, etc.

Use of parts not supplied by Wayne-Dalton Corp. may cause

the Opener to malfunction and create unsafe conditions.

7. Wear safety glasses for eye protection when installing or

servicing the Opener or door.

8. Install Opener on a properly balanced and operating garage

door. Have a qualified service person make adjustments/

repairs to cables, spring assemblies, and other hardware

before installing the Opener. An improperly balanced door

could cause severe injury.

9. Where possible, install the Opener seven feet or more above

the floor. Mount the Emergency Disconnect six feet above

the floor.

10. Locate the Wall Station: (a) within sight of door, (b) at a

minimum height of five feet, so small children cannot reach it,

and (c) away from all moving parts of the door.

11. After installing the Opener, the door MUST reverse when it

contacts a 1- 1/2” high object (or 2 x 4 board laid flat) on
the floor. The door MUST also reverse when a 6” high object is
placed on the floor in line with safety sensors.

12. Installation and wiring must comply with local building and

electrical codes. Connect the Power Cord to a properly

grounded outlet. Do not remove the ground pin from

Power Cord.

After installation is complete, fasten this
manual near garage door. Perform Monthly
obstruction test and maintenance as
recommended. See pages 23 and 31.

WARNING

Table of Contents

Package Contents ............................................................................... I.

Pre-Installation Inspection ................................................................... II-III.

Tools Needed ...................................................................................... III.

Important Safety Instructions .............................................................. IV.

Torsion idrive Installation ..................................................................... 1-16.

Pre-Operation Installation .................................................................... 17-25.

Operation ............................................................................................ 26-31.

Maintenance ....................................................................................... 31.

Troubleshooting ................................................................................... 32-33.

Warranty ............................................................................................. 33.

Customer Service Number .................................................................. 34.

Содержание IDrive 3651-372











































Результаты поиска

Содержание IDrive 3651-372

Отзывы:

Похожие инструкции для IDrive 3651-372

Бренды по названию

Популярные бренды

Wayne-Dalton IDrive 3651-372, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание IDrive 3651-372

Отзывы:

Похожие инструкции для IDrive 3651-372

Бренды по названию

Популярные бренды