background image

The adjacent bottom corner 

bracket and all cable 

retention features including 

milford pins, cotter pins, & 

clevis pins are under HIGH 

SPRING TENSION.

262484  REV1 01/08/10

WARNING

Repairs and adjustments 

must be made by an 

experienced door 

professional or mechanic, 

using proper tools and 

instructions.

DO NOT REMOVE, COVER OR 

PAINT THIS LABEL.

© Copyright 2010 Wayne-Dalton, 
a Division of Overhead Door Corp.

The adjacent bottom corner 

bracket and all cable 

retention features including 

milford pins, cotter pins, & 

clevis pins are under HIGH 

SPRING TENSION.

262484  REV1 01/08/10

WARNING

Repairs and adjustments 

must be made by an 

experienced door 

professional or mechanic, 

using proper tools and 

instructions.

DO NOT REMOVE, COVER OR 

PAINT THIS LABEL.

© Copyright 2010 Wayne-Dalton, 
a Division of Overhead Door Corp.

WHEN CONNECTING A TROLLEY TYPE GARAGE DOOR 

OPENER TO THIS DOOR, A WAYNE-DALTON 

OPENER/TROLLEY BRACKET MUST BE SECURELY 

ATTACHED TO THE TOP SECTION OF THE DOOR, ALONG 

WITH ANY U-BARS PROVIDED WITH THE DOOR. THE 

INSTALLATION OF THE OPENER MUST BE ACCORDING TO 
MANUFACTURER’S INSTRUCTIONS AND FORCE SETTINGS 

MUST BE ADJUSTED PROPERLY.

323917                              REV2   01/15/2010

IMPORTANT!

Copyright 2010 Wayne Dalton, a Division of Overhead Door Corp.

Spring Turns

Door Height

Spring Turns

     (6’ - 0”)

14

     (6’ - 3”)

14 - 1/2

     (6’ - 5”)

15

     (6’ - 6”)

15

     (6’ - 8”)

15 - 1/2

     (6’ - 9”)

15 - 1/2

     (7’ - 0”)

16

     (7’ - 3”)

16 - 1/2

     (7’ - 6”)

17

     (7’ - 9”)

17 - 1/2

     (8’ - 0”)

18

Number of Installed Spring Turns

300547                  REV2   01/15/2010

Copyright 2010 Wayne Dalton, a 
Division of Overhead Door Corp.

HIGH SPRING TENSION CAN CAUSE 
SERIOUS INJURY OR DEATH.

DO NOT

 adjust, repair or remove springs or parts to 

which springs are connected, such as steel brack-
ets, cables, wood blocks, fasteners or other parts of 
the counterbalance system.

Adjustments or repairs must 

ONLY

 be made by a 

trained door systems technician using proper tools 
and instructions.

DO NOT

 remove, cover or paint over this tag. Prod-

uct user should inspect this tag periodically for 
legibility and should order a replacement tag from 
the door manufacturer, as needed.

©Copyright 2010 Overhead Door Corporation                                                     

102081   REV2 06/24/2010

SAFETY INSTRUCTIONS

1.

  Operate door ONLY when it is properly   

 adjusted and free of obstructions.

2.

  If a door becomes hard to operate,  

 

 

inoperative or is damaged,  immediately  

 

have necessary adjustments and/or repairs  

 

made by a trained door system technician  

 

using proper tools and instructions.

3.

  DO NOT stand or walk under a moving door,  

 

or permit anybody to stand or walk under  

 

an electrically operated door.

4.

  DO NOT place fingers or hands into open  

 

section joints when closing a door. Use lift  

 

handles/gripping points when operating  

 door manually.

5.

  DO NOT permit children to operate garage  

 door or door controls.

6.

  Due to constant extreme spring tension,  

 

DO NOT attempt any adjustment, repair or  

 

alteration to any part of the door,  

 

 

especially to springs, spring brackets,    

 

bottom corner brackets, red colored    

 

fasteners, cables or supports. To avoid   

 

possible severe or fatal injury, have any  

 

such work performed by a trained door  

 

system technician using proper tools and  

 

instructions.

7.

  On electrically operated doors, pull down  

 

ropes must be removed and locks must be  

 

removed or made inoperative in the open  

 (unlocked) position.

8.

  Top section of door may need to be    

 

reinforced when attaching an electric    

 

opener. Check door and/or opener  

 

 

manufacturer’s instructions.

9.

  VISUALLY inspect door and hardware    

 

monthly for worn and/or broken parts.   

 

Check to ensure door operates freely.

10.

 Test electric opener’s safety features    

 

monthly, following opener manufacturer’s  

 

instructions.

11.

 NEVER hang tools, bicycles, hoses, clothing  

 

or anything else from horizontal tracks.  

 

Track systems are not intended or designed  

 

to support such extra weight. 

Place label at a readable height on door. DO NOT  

remove, cover or paint over this label. Product 

user should inspect this label periodically for 

legibility and should order a replacement label 
from the door manufacturer as needed.

324100              REV7   09/16/2013

Quality garage doors since 1954

Wayne Dalton

2501 S. State Hwy 121 Bus., Suite 200

Lewisville, TX 75067

For service, call (800) 827-3667

www.Wayne-Dalton.com

Copyright 2013 Wayne Dalton, a

Division of Overhead Door Corp.

 

Residential warning label 

The warning label will either be on 

the right or the left end stile.

Drawbar operator 

bracket label

Bottom corner bracket warning labels

Torsion spring tag(s) 

(one per spring)

TorqueMaster

®

 Plus tag(s) 

(one per spring)

20

Содержание 9100























Отзывы: