19
Please Do Not Return This Product To The Store.
Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer
section online at
www.wayne-dalton.com
Tools Needed:
Tools Needed:
iNST
alla
Tio
N
center bearing bracket
Power Drill
7/16” Socket Driver
Level
Tape Measure
Pencil
1/4” Torx Bit
Step Ladder
Measure to locate the center of the door and mark
a vertical pencil line on the mounting surface above
the door, to indicate the center line of the door. Then,
measure from the center of the bearing, in one of
the end bearing brackets, DOWN to the top of the
door. Using that dimension, measure UP from the top
of the door and mark a horizontal pencil line on the
mounting surface, intersecting the vertical pencil line.
Now align the edge of the center bearing bracket
along the vertical pencil line on the mounting surface.
Center the bearing bracket on the horizontal line.
This will ensure the torsion tube is level between the
center and end bearing brackets. Attach the center
bearing bracket, in this location, to the mounting
surface, using (2) 5/16” x 1-5/8” lag screws and (1)
5/16” x 2” tamper-resistant lag screw.
imPoRTaNT:
USE ThE 5/16” X 1-5/8” TAMPER-
RESISTANT LAG SCREW ONLY If MOUNTING SURfACE
MOUNTED OVER MASONRY. TAMPER-RESISTANT LAG
SCREW MUST BE ATTAChED ThROUGh ThE BOTTOM
hOLE Of ThE CENTER BEARING BRACkET.
Vertical
line
Mounting
surface
Equal
distance
Center of end
bearing bracket
horizontal
line
Center bearing bracket
Mounting
surface
horizontal line
Center bearing
bracket
(1) 5/16” x 1-5/8”
Lag screw
(1) 5/16” x 1-5/8”
Lag screw
Vertical line
19
(1) 5/16” x 2”
Tamper-resistant
lag screw or (1)
5/16” x 1-5/8” lag
screw
Torsion end bearing brackets
End bearing brackets are right and left
hand. Break the end bearing brackets
apart.
Starting on the left hand side and using
the upper slots in the end bearing
bracket, position above the flagangle
and secure the end bearing bracket to
the horizontal angle using (2) 3/8”-16
x 3/4” truss head bolts and (2) 3/8”-16
nuts.
imPoRTaNT:
END BEARING BRACkETS
MUST BE ATTAChED ThROUGh ThE
LOWER SLOTS ON 12” RADIUS TRACk.
15” RADIUS TRACk MUST USE ThE UP-
PER SLOTS ON ThE BRACkET.
Once the bracket is secured to the
horizontal angle, secure the top of the
end bearing bracket to the jamb using
(1) 5/16” x 1-5/8” lag screw. Repeat for
right hand side.
NoTe:
Right and left hand is always
determined from inside the building
looking out.
Step L
adder
Power Drill
Ratchet Wrench
7/16” Socket
Driver
9/16” Socket
Driver
9/16” Wrench
LEfT hAND END BEARING
BRACkET
UPPER SLOTS
USED ON 15”
RADIUS TRACk.
LOWER SLOTS
ON 12” RADIUS
TRACk.
(1) 5/16” X 1-5/8”
LAG SCREW
(2) 3/8”-16 X 3/4”
TRUSS hEAD BOLTS
(2) 3/8”-16 NUTS
18
hORIzONTAL
ANGLE
LEfT hAND
END BEARING
BRACkET
RIGhT hAND END
BEARING BRACkET
BREAk
ThE END
BEARING
BRACkETS
APART
hORIzONTAL
ANGLE
