![background image](http://html1.mh-extra.com/html/wayne-dalton/8124/8124_installation-instructions-and-owners-manual_3975075010.webp)
10
Please Do Not Return This Product To The Store.
Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer
section online at
www.wayne-dalton.com
Tools Needed:
1
2
3
4
#1 Wide hinge
#2 Wide hinge
Roller
placement
6
hinges
Power Drill
7/16” Socket Driver
#3 Wide hinge
#4 Wide hinge
Roller
placement
Roller
placement
Roller
placement
hinge Schedule
Option
Code
End hinges
Wide Center
hinges
Narrow
Center
hinges
quantity # Of
hinges per section
Wide End
hinges
1300
2
Yes
None
As required
1320
4
Yes
As required
None
1340
4
Yes
As required
None
1
#1 Narrow hinge
NoTe:
Refer to the door section identification on
page 4 to determine your lock (second), intermediate
(third), intermediate II (fourth section on a five section
door), and top sections. Measure your sections to
make sure they are the correct height as indicated
on the chart.
Refer to the hinge schedule to determine the ap-
propriate hinges for your door.
FoR wiNDloaD oPTioN coDeS (a): 1300:
One wide end hinge, narrow center hinge and a short
stem roller are required, per side.
FoR wiNDloaD oPTioN coDeS (b): 1320 and
1340:
Two wide end hinges, wide center hinge(s) and
a long stem roller are required, per side.
Locate the bottom section, using #1 hinges for the
end stiles and depending on the width of your door,
enough #1 hinge(s) for each of the center stile(s)
location.
Place the hinges on the section so that the lower (#)
leaf of the hinge is over the pre-punched holes in
the #1 and #4 of the end stiles and the pre-punched
holes of the center stile(s) at the top of the section.
Secure the hinges to the section using (2) 1/4” - 14
x 7/8” self tapping screws for each, then insert the
roller into the appropriate end hinge tube.
NoTe:
#1 wide hinges serve as end hinges and cen-
ter hinges on the bottom section. #1 wide or narrow
hinges serve as center hinges on all other sections.
Refer to hinge schedule chart.
Use #2 end hinges and #1 center hinges for the lock
section (second section) of the door.
Use #3 end hinges and #1 center hinges for the
intermediate section (third section) of the door.
Use #4 end hinges and #1 center hinges for the
intermediate section II (fourth section) of the door.
imPoRTaNT:
WhEN PLACING ROLLERS INTO END
hINGES NUMBER 2 AND hIGhER, ThE ROLLER GOES
INTO TUBE fURThEST AWAY fROM SECTION.
NoTe:
#4 End hinges are used on fourth section of
five section doors.
1
1
Previously installed
Wide end hinge
Long stem roller
Wide end hinge
(2) 1/4”- 14 X 7/8”
Self drilling screws
Stile
(b)
Typical
center hinge
(2) 1/4”- 14 x 7/8”
Self drilling screws
Center
stile
(a oR b)
1
(a oR b)
(2) 1/4”- 14 x 7/8”
Self drilling screws
Wide end hinge
Short stem
roller
End stile
Pre-punched
holes
Pre-punched
holes
Pre-punched
holes