NOTE:
Drill a 3/16” pilot hole in the mounting surface to avoid splitting the lumber. Do not
attach the mounting surface with nails.
WEATHERSTRIPS (MAY NOT BE INCLUDED):
Depending on the size of your door, you may have to cut or trim the weatherstrips (if neces-
sary) to properly fit into the header and jambs.
NOTE:
If nailing product at 40°F or below, pre-drilling is required.
NOTE:
Do not permanently attach weatherstrips to the header and jambs at this time.
For the header, align the weatherstrip 1/8” to 1/4” inside the header edge, and temporarily
secure it to the header with equally spaced nails. Starting at either side of the jamb, fit the
weatherstrip up tight against the temporarily attached weatherstrip in the header and 1/8”
to 1/4” inside the jamb edge. Temporarily secure the weatherstrip with equally spaced nails.
Repeat for other side. This will keep the bottom section from falling out of the opening during
installation. Equally space nails approximately 12” to 18” apart.
HEADROOM REQUIREMENT:
Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2” (64 mm) of additional headroom is required.
NOTE:
6” low headroom conversion kit is available for 12” radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT:
Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
*NOTE:
For door heights from 10’1” to 14’0”, refer to your operator manufacture installation
instructions for appropriate depth into room.
BACKROOM REQUIREMENTS
Door Height
Track
Manual Lift
Motor Operated
6’0” to 7’0”
15” Radius
102” (2591 mm)
125” (3175 mm)
7’1” to 8’0”
15” Radius
114” (2896 mm)
137” (3480 mm)
8’1” to 9’0”
15” Radius
126” (3200 mm)
168” (4267 mm)
9’1” to 10’0”
15” Radius
138” (3505 mm)
168” (4267 mm)
HEADROOM REQUIREMENTS
Track Type
Space Needed
15” Radius
14-1/2” (368 mm)
Weatherstrips
Level header
Finished
Door width
Jambs
Backroom
Plumb
jambs
Finished
Door
Height
Nail
Headroom
Header board 2”x 6”
lumber preferred
Suitable mounting surface
2”x 6” lumber minimum
Weatherstrips
Jamb
Quick Install track
Other track systems
Jamb
1/8” to 1/4”
Min. Side
room
Clearance
is 3-1/2”
Min. Side
room
Clearance
is 3-1/2”
Package Contents
NOTE:
Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Door sections (as required)
Torsion shaft / Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Vertical tracks RH/LH (as required)
Horizontal tracks RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Angle mount vertical track assemblies RH/LH (as required)
Fully Adjustable flag angles
RH/LH (as required)
Track rollers
Strut
(if included)
Tandem track rollers
(if included)
Weather seals & nails
(If included)
F.A. jamb brackets
(as required)
Top fixture bases
(as required)
Top fixture slides
(as required)
“L” Reinforcing
brackets (if included)
(2) Bottom corner
brackets (as required)
(2) Spacers
(as required)
Hinges (as required)
Cotter pin (as required)
5/16” x 1-1/4”
Clevis pin (as required)
Bottom weather
seal (as required)
Strut clips
(as required)
(2) Bottom corner
brackets (as required)
Track roller carriers
(as required)
3