background image

Warranty

 

Rev. 06.2014 

 

 

 

7400 Series 

Limited Warranty 

 

Wayne Dalton, a division of Overhead Door Corporation ("Seller") warrants to the original purchaser of the 

Model Series 

7400

 

(“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free 

from defects in materials and workmanship for a period of 

One (1) year

, measured from the date of installation: 

 

Seller’s obligation u

nder this warranty is specifically limited to repairing or replacing, at its option, any part which is 

determined by Seller to be defective during the applicable warranty period. Any labor charges are excluded and will be the 
responsibility of the purchaser.  

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This 
warranty is made to the original purchaser of the Product only, and is not transferable or assignable. This warranty applies 
only to Product installed in a residential or other non-commercial application. It does not cover any Product installed in 
commercial or industrial building applications. This warranty does not apply to any unauthorized alteration or repair of the 
Product, or to any Product or component which has been damaged or deteriorated due to misuse, neglect, accident, 
puncture, drilling of holes (other than as directed by Seller), incorrect installation of hardware, fire, failure to provide 
necessary maintenance, normal wear and tear, exposure to salt or other corrosive environments, or acts of God or any other 
cause beyond the reasonable control of Seller. This warranty also specifically excludes all refinishing costs and any 
inconsistencies or occurrences related to the characteristics or attributes of natural wood, including but not limited to: (i) 
variations in the color or grain of Product sections, (ii) the emission or secretion of tannins from the Product sections which 
may stain or alter the color of a painted Product, and (iii) cracking, checking, lifting wood grain or cracking due to natural 
expansion and contraction of the Product sections.  

SPECIAL PAINTING REQUIREMENTS: This warranty shall be void if the Product sections are not painted or sealed in 
accordance with DASMA TDS 162 (available at www.dasma.com) on all sides, including all edges with one (1) coat of 
exterior grade primer (or stain) and two (2) coats of high quality acrylic latex exterior grade finish paint (or sealer), applied in 
accordance with the pain

t or Sealer manufacturer’s instructions and Seller’s painting and maintenance instructions. Sections 

must be finished within five (5) days of receipt and prior to installation. Damage caused by exposure of the product to water, 
moisture, sun or other conditions prior to completion of painting (or Sealing) is excluded. This warranty shall also be void if 
the Product is painted a dark color, including but not limited to black, dark grey, dark green and dark brown*. IMPROPER 
TRANSPORTATION, STORAGE OR DELAYS IN FINISHING, THAT ALLOWS EXPOSURE OF THE WOOD DOOR 
SURFACES TO MOISTURE OR OTHER CONTAMINANTS WILL RESULT IN THE WARRANTY BEING VOIDED. 

ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY 
IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME 
TO THE APPLICABLE WARRANTY PERIOD REFLECTED ABOVE. NO WARRANTIES, WHETHER EXPRESS OR 
IMPLIED, WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED. Some states do not allow limitations 
on how long an implied warranty lasts, so the above limitation may not apply to you. 

IN NO EVENT SHALL SELLER BE RESPONSIBLE FOR, OR LIABLE TO ANYONE FOR, SPECIAL, INDIRECT, 
COLLATERAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES, even if Seller has been advised of the 
possibility of such damages. Such excluded damages include, but are not limited to, loss of use, cost of any substitute 
product, or other similar indirect financial loss. Some states do not allow the exclusion or limitation of incidental or 
consequential damages, so the above limitation or exclusion may not apply to you. 

Claims under this warranty must be made promptly after discovery, within the applicable warranty period, and in writing to 
the Seller whose name and address appear below. The purchaser must allow Seller a reasonable opportunity to inspect any 
Product claimed to be defective prior to removal or any alteration of its condition. Proof of the purchase and/or installation 
date, and identification as the original purchaser, may be required. There are no established informal dispute resolution 
procedures of the type described in the Magnuson-Moss Warranty Act. 

* Dark colors shall mean colors as dark as or darker than any of the following Sherwin-Williams Exterior Colors: 7069 Iron 
Ore (dark grey), 6447 Evergreens (dark green) or 7510 Chateau Brown (dark brown). 
 
SELLER:  

 

 

 

 

 

 

 

 

 

 

 

 

SELLER’S ADDRESS: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание 7400 Series

























Отзывы: