Top fixture
base
(1) 5/16”-18
Hex nut
Top fixture
slide
(1) 5/16”-18 x 3/4”
Carriage bolt
“L” Reinforcing
bracket (if applicable)
Starting on the left hand side of the top section, align the lip of the top fixture base on top
of the corner of the top section and even with the edge of the section. Place the strut on the
top edge of the top section and on top of the top fixtures, as shown. Center the strut side to
side on the section. Secure strut to the section using 1/4” - 20 x 7/8” self drilling screws at
each end and at each center hinge(s) / dimple location(s). Secure the top fixture and the “L”
reinforcement bracket (if applicable) to the top section through the end cap using 1/4” - 20 x
11/16” self drilling screws.
If applicable, repeat for other top fixture assembly(s). Repeat the same process for other side.
Insert short / long stem track roller into top fixture slide(s).
NOTE:
If your door came with two top fixtures, then one top fixture and a short stem track
roller are required for each side.
NOTE:
If your door came with four top fixtures, then two top fixtures and a long stem track
roller are required for each side.
The fixture will be tightened and adjusted later, in step, Adjusting Top Fixtures.
Top fixture
base
End
cap
Short stem
track roller
Strut
Top section
“L” Reinforcing
bracket (if applicable)
1/4”-20 x 11/16”
Self drilling screws
Top fixture
slide
1/4”-20 x 7/8”
Self drilling screws
Top fixture
bases
End cap
Long stem
track roller
Top section
“L” Reinforcing bracket
(if applicable)
(6) 1/4”-20 x 11/16”
Self drilling screws
Top
fixture
slide
Top fixture
slide
Strut
“L” Reinforcing brackets
(if applicable)
(2) 1/4”-20 x 7/8”
Self drilling screws
(2) 1/4”-20 x 7/8”
Self drilling screws
Attaching Strut To Lock or Intermediate Sec-
tions
9
NOTE:
Depending on the size of your door, your Lock or Intermediate(s) section may require
struts.
Using sawhorses, lay the Lock / Intermediate section on a flat smooth surface. Referring
to the Lock, Intermediate(s) Section Strutting Schedule below, determine if your Lock or
Intermediate(s) is required for strutting.
Lock, Intermediate(s) Section Strutting Schedule
Door Height
# Of Sections
Door Width
12’0” - 14’0”
15’0” - 18’0”
20’0”
6’6” - 8’0”
4
2” Strut, Top of
Lock section
2” Struts, Top
of Intermediate
I section, Top of
Lock section
3” Struts, Top
of Intermediate
I section, Top of
Lock section
Lock, Intermediate(s) Section Strutting Schedule
Door Height
# Of Sections
Door Width
12’0” - 14’0”
15’0” - 18’0”
20’0”
8’3” - 10’0”
5
2” Strut, Top of
Intermediate I
section
2” Struts, Top of
Intermediate II
section, Top of
Intermediate I
section, Top of
Lock section
3” Struts, Top of
Intermediate II
section, Top of
Intermediate I
section, Top of
Lock section
10’3” - 12’0”
6
2” Struts, Top of
Intermediate III
section, Top of
Intermediate I
section
3” Struts, Top of
Intermediate III
section, Top of
Intermediate I
section,
3” Struts, Top of
Intermediate III
section, Top of
Intermediate II
section, Top of
Intermediate I
section, Top of
Lock section
12’2” - 14’0”
7
2” Struts, Top of
Intermediate V
section, Top of
Intermediate III
section, Top of
Intermediate I
section
3” Struts, Top of
Intermediate VII
section, Top of
Intermediate V
section, Top of
Intermediate III
section, Top of
Intermediate I
section,
3” Struts, Top of
Intermediate V
section, Top of
Intermediate IV
section, Top of
Intermediate III
section, Top of
Intermediate II
section, Top of
Intermediate I
section, Top of
Lock section
Place the strut on the appropriate section up against the bottom of the hinges. Center the
strut side to side on the section. Secure the strut to the section using (2) 1/4” - 20 x 7/8” self
drilling screws at each end hinge location and (2) 1/4” - 20 x 7/8” self drilling screws at each
center hinge(s) / dimple location(s).
Single Endstiles:
Endcaps
Typical section
Strut
1/4”-20 x 7/8” Self drilling screw locations
Double Endstiles:
Endcaps
Typical section
Strut
1/4”-20 x 7/8” Self drilling screw locations
Center hinge(s)
Center hinge(s)
Attaching Inside Lift Handles
10
NOTE:
Refer to door section identification, located in the pre-installation section of this
manual to determine what size sections you need to use as your bottom section and lock
(second) section.
Starting on the left hand side and on the inside portion of bottom section, position the inside
lift handle on top of the end cap. Keeping the inside lift handle vertically aligned and centered
on the end cap. Secure the lift handle to end cap using (2) 1/4” - 20 x 11/16” self-drilling
screws. Next, install the second inside lift handle in the same manner as the first onto the
lock section (second section).
IMPORTANT:
THE INSIDE LIFT HANDLES NEED TO BE VERTICALLY ALIGNED WITH EACH
OTHER.
Lift handle
End cap
Bottom and or
Lock section
(2) 1/4”-20 x 11/16”
Self drilling screws
Lift handle
installed
End cap
Bottom and or
Lock section
Attaching Outside Pull Handles
11
10
