12” to 18” apart.
FOR FULLY ADJUSTABLE TRACK:
For the header, align the weatherstrip 1/8” to 1/4” inside
the header edge, and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and 1/8” to 1/4” inside the jamb edge. Temporarily secure the
weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec-
tion from falling out of the opening during installation. Equally space nails approximately 12”
to 18” apart.
HEADROOM REQUIREMENT:
Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2” (64 mm) of additional headroom is required.
NOTE:
6” low headroom conversion kit is available for 12” radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT:
Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
*NOTE:
For door heights from 10’1” to 14’0”, refer to your operator manufacture installation
instructions for appropriate depth into room.
BACKROOM REQUIREMENTS
Door Height
Track
Manual Lift
Motor Operated
6’0” to 7’0”
12”, 15” Radius
102.5” (2601 mm)
125” (3175 mm)
7’1” to 8’0”
12”, 15” Radius
114.5” (2908 mm)
137” (3480 mm)
8’1” to 9’0”
12”, 15” Radius
127” (3226 mm)
168” (4267 mm)
9’1” to 10’0”
12”, 15” Radius
139” (3531 mm)
168” (4267 mm)
10’1” to 12’0”
12”, 15” Radius
163.5” (4153 mm)
See *NOTE
12’1” to 14’0”
12”, 15” Radius
187.5” (4763 mm)
See *NOTE
HEADROOM REQUIREMENTS
Track Type
Space Needed
12” Radius
12-1/2” (318 mm)
15” Radius
14-1/2” (368 mm)
Weatherstrips
Level heade
r
Finished
Door width
Jamb
s
Backroo
m
Plumb
jambs
Finished
Door
Height
Nail
Headroom
Header board 2”x 6”
lumber preferred
Suitable mounting surface
2”x 6” lumber minimum
Weatherstrips
Jamb
Quick Install track
Other track systems
Jamb
1/8” to 1/4”
Min. Side
room
Clearance
is 3-1/2”
Min. Side
room
Clearance
is 3-1/2”
Package Contents
NOTE:
Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Door sections (as required)
Torsion shaft / Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Vertical tracks RH/LH (as required)
F.A. flag angles RH/LH (as required)
Horizontal tracks RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Angle mount vertical track assemblies RH/LH (as required)
F.A. jamb brackets
(as required)
Weather seals & nails
(If included)
Drawbar operator
bracket (if included)
Bottom corner
brackets (as required)
Bottom corner brackets
RH/LH (as required)
Bottom corner
brackets (as required)
Track roller carriers
(as required)
Strut (U-shaped)
(if included)
Bottom corner brackets
RH/LH (as required)
(2) Bottom corner
brackets (as required)
Bottom corner
brackets (as required)
Top fixture assemblies
(as required)
Top fixture bases
(as required)
Top fixture slides
(as required)
“L” Reinforcing brackets
(as required)
Pull down rope
(if included)
Inside lift handles
Lift handles
Pull handles
Graduated hinges
(as required)
Track rollers
(as required)
Torsion springs RH/LH
Counterbalance
lift cables
Center bracket
bushing (as required)
3
