background image

Multi-Function Remote

Œ

 Remote Housing: This 2-piece housing design provides both convenient mounting and simple 
dissasembly for customization. The integrated screw mount tabs are scored to aid removal if securing 
by another method and the lower housing can be detatched by removing the two top screws for 
reducing weight or size. For panel mounting, the housing can be completely disassembled by also 
removing the knob, shaft nut, and circuit board screw. It is recommended to protect the exposed PCB 
with heat shrink. For LED relocation, carefully release the LED from the back side of the snap ring, 
then push the snap ring though to the front to remove. Follow the reverse process for re-mounting.



Rotary Encoder:  This control knob is for adjusting CH1/2/3/4/5/6 master volume, CH5/6 level and 
source selection (toggle). The factory setting for knob function is CH5/6 output level adjustment only 
for a speaker level source. Other knob functions can be enabled via the dip-switches at the back of the 
remote (see 



 below). To toggle between Main and AUX sources, short-press the knob. To activate 

the selected source’s CH5/6 level mode, long-press for 2 seconds.  To reset to factory defaults for the 
selected system type, long-press the knob for >5 seconds. 

Ž

Source/Function LED:  Depending upon which system type is selected (see 



 below), this LED will 

indicate which source and level mode is currently selected. There are four LED modes: solid red, 
flashing red, solid blue and flashing blue. In the default system Type-1, the only LED indication is solid 
red when the link6 is powered on. For the other three system types, solid red indicates Main speaker 
level source is selected and solid blue is for AUX source. Flashing indicates CH5/6 level mode is active 
for the current source, which will timeout after 5 seconds if no adjustments are made.



System Type Select:

  

 These dip-switches are for selecting one of four available system types for 

setting which knob functions and priority are enabled. Note that the up/down position for each switch 
is when looking at the back of the remote as shown above. Switch settings can be changed at any time 
on the remote without requiring access to the main link8 unit.



Œ

Ž





Type-2: Main CH5/6 Level, AUX Volume & AUX CH5/6 Level 

For systems using the factory radio as the master volume for Main speaker level input and an 
auxiliary source is connected to the link6’s AUX input. When Main source is selected, the knob 
adjusts CH5/6 level only. When AUX source is selected, knob priority is AUX volume and its  
CH5/6 level mode can be selected with a 2sec long-press. 

Type-3: AUX Volume & AUX CH5/6 Level 

For stand-alone applications without a factory radio where only the link6’s AUX input is used as 
the system source. In this setting, AUX CH5/6 level mode can be accessed with a 2sec long-press, 
while short-press for source select is disabled so cannot be accidentally changed.

Type-4: Master Volume & CH5/6 Level

This setting is primarily for systems where factory radio volume is not used (e.g. fixed input 
signal level, volume dependent EQ, etc.), and that may also have an AUX source connected to 
the link6. In system Type-4, all knob functions are enabled. When either Main or AUX input is 
selected, knob priority is master volume for that source. Independent CH5/6 level adjustment 
is also accessable for each source with a 2sec long-press.



 Remote Level Control Jack:  This RJ45 jack is for connecting the remote to the RLC port on the main 
link6 unit with the supplied cable. A standard 8-conductor ethernet cable may also be used.

 

Note:

  The link6 will remember all level settings and which source was selected at last power off and 

return at next power on, even if the battery is disconnected. However, if the remote is disconnected at 
power on, the memory will be overridden to factory defaults and all levels will return to maximum 0dB.

4

Type-1: Main CH5/6 Level Only (factory setting)

For systems where only subwoofer level control is needed with a speaker level source, and no 
AUX source is connected to the link6. In this setting, the knob’s short-press and long-press 
functions (except reset) are disabled to prevent accidental selection.

Содержание Link6













Отзывы: