wattstopper DT-200 Скачать руководство пользователя страница 4

Страница: 4 / 12

WIRING DIRECTIONS

Each WattStopper B series power pack can supply power for up to 2 DT-200
sensors. Each WattStopper BZ series power pack can supply power for 3 DT-200
sensors. When using more sensors than this, multiple power packs are required.

Refer to the wiring diagram on the next page for the following procedures:

Connect the

LOW VOLTAGE

• RED wire (+24VDC) from power pack to the

violet

wire on the sensor.

• BLACK wire (Return) from power pack to the

gray

wire on the sensor.

Wiring a

SINGLE LIGHTING LOAD CONTROLLED BY OCCUPANCY

– connect:

• BLUE wire from power pack to the

yellow

wire on the sensor.

To add a

MOMENTARY MANUAL SWITCH

such as the LVS-1 Momentary Toggle

Switch, to the above applications–connect:

• Wire from one side of switch to the

green

wire on sensor.

• Wire from other side of switch to the

gray

wire on sensor.

Wiring the

ISOLATED RELAY

: (The Isolated Relay is rated for 1A@30VAC/VDC)

Connect the wires necessary to the application that requires this output:

• Relay Common (must be used for proper operation) is the

red

wire

• N.O. (Normally Open)–Closed when occupancy is detected, is the

orange

wire

• N.C. (Normally Closed)–Open when occupancy is detected, is the

brown

wire

CAUTION

TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE

INSTALLING POWER PACKS OR SENSORS.

Call 800.879.8585 for Technical Support

Содержание DT-200













Результаты поиска

Содержание DT-200

Отзывы:

Похожие инструкции для DT-200

Бренды по названию

Популярные бренды

wattstopper DT-200, Руководство по установке

Результаты поиска

Содержание DT-200

Отзывы:

Похожие инструкции для DT-200

Бренды по названию

Популярные бренды