Watts W110 LXT страница 29 Скачать руководство пользователя

Страница: 29 / 32

Troubleshooting SXT

Error Codes

NOTE: Error codes appear on the In Service display.

Error Code

Error Type

Cause

Reset and Recovery

Motor Stall /Cam Sense

Error

No state changes in the optical sensor

are detected for 6 seconds.

Unplug the unit an plug back in. Allow the control to attempt to find position again.

Verify the optical sensor is in place with the wires connected to the circuit board.

Verify the motor and drive train components are in good condition and assembled

properly. Check the valve and verify that the piston travels freely. Replace/reassemble

the various components as necessary.

Plug the unit back in and observe its behavior. If the error reoccurs, unplug the unit,

put it into bypass and contact technical support.

Motor Run-On Error /

Cycle Sense Error

An undesired optical sensor state

change occurred.

Non-critical error. Extra optical sensor pulse detected. Press any button to clear the

error. Press extra cycle button to advance motor to clear error.

Regen Failure

The system has not regenerated for

more than 99 days (or 7 days if the

Control Type has been set to Day-of-

Week).

Perform a Manual Regeneration to reset the error code.

If the system is metered, verify that it is measuring flow by running service water and

watching for the flow indicator on the display. If the unit does not measure flow, verify

that the meter cable is connected properly and that the meter is functioning properly.

Enter Master Programming Mode and verify that the unit is configured properly, For

the valve configuration. Check that the correct system capacity has been selected,

that the day override is set properly, and that meter is identified correctly. If the unit

is configured as a Day-of-Week system, verify that at least one day is set ON. Correct

the setting as necessary.

Memory Error

Control board memory failure.

Perform a Master Reset and reconfigure the system via Master Programming Mode.

After reconfiguring the system, step the valve through a manual regeneration. If error

continues, call technical support.

Fail Safe Error

Valve has failed to find position in one

minute.

Unplug the unit and plug it back in. If error continues, call technical support.

29 W110 LXT Downflow Softeners and SXT Filters

Содержание W110 LXT

































Результаты поиска

Содержание W110 LXT

Отзывы:

Похожие инструкции для W110 LXT

Бренды по названию

Популярные бренды

Watts W110 LXT, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание W110 LXT

Отзывы:

Похожие инструкции для W110 LXT

Бренды по названию

Популярные бренды