background image

 

4.  Technical Information 

Operating Temperature 

32°F to 104°F (0°C to 40°C) 

Storage Temperature 

-4°F to 122°F (-20°C to 50°C) 

Operating Humidity 

0 to 100% humidity 

Batteries 

2 AA (included) 

Weight 

3.5 oz (100 g) without batteries 

Size 

Diameter: 3

⅜ inch (85 mm) 

Height: 1 11/16 inch (43 mm) 

RF Range 

915 MHz 

Approvals 

FCC, IC, IP Waterproof Class IP67 

FCC ID

: 2AFJT-CIMDOF18815 

IC ID

: 20938-CIMDOF18815 

FCC: This product has been tested and found to comply with FCC part 15 subpart C. Operation 
is subject to the following two conditions: (1) this device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference that may cause 
undesired operation of the device. However, there is no guarantee that interference will not 
occur in a particular installation. If this device does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures: 

 Reorient or relocate the receiving antenna. 

 Increase the separation between the equipment and receiver. 

 Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 

 Consult the dealer or an experienced radio/TV technician for help. 

Warning

: Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

Industry Canada 

This Device complies with Industry Canada License-exempt RSS standard(s). Operation is 
subject to the following two conditions: (1) this device may not cause interference, and (2) this 
device must accept any interference, including interference that may cause undesired operation 
of the device under Industry Canada regulations. 

Le présent appareil est conforme aux CNR d

’Industrie Canada applicables aux appareils radio 

exempts de licence. L

’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne 

doit pas produire de brouillage, et (2) l

’utilisateur de l’appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est susceptible d

’en compromettre le 

fonctionnement. 

Warning: FCC and IC Radiation Exposure Statement 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. The antenna(s) used for this equipment must be installed to provide a separation 
distance of at least 8 inches (20 cm) from all persons. 

Cet équipement est conforme à l

’exposition aux radiations de FCC et d’Industrie Canada 

établies pour un environnement non contrôlé. L

’antenne (s) utilisé pour cet équipement doit être 

installé pour fournir une distance d

’au moins 20 cm à partir de toutes les personnes. 

Содержание H2iQ Series











Отзывы: