Watts Aerco Benchmark OMM-0116 Скачать руководство пользователя страница 90

Страница: 90 / 126

Benchmark 750-3000 Installation & Startup Manual

SECTION 5

– SAFETY DEVICE TESTING

OMM-115_D

•

GF-200

•

5/9/2019

Technical Support

•

(800) 526-0288

•

Mon-Fri, 8 am - 5 pm EST Page 90 of

126

5.7 FLAME FAULT TEST

Flame faults can occur during ignition or while the unit is already running. To simulate each of
these fault conditions, proceed as follows:

Flame Fault Test Instructions

1. Set the ON/OFF switch to the

OFF

position.

2. Place the unit in the MANUAL mode and set the valve position

between 25% and 30%

3. Close the manual gas shutoff valve located between the Safety Shut-Off Valve (SSOV)

and the Air/Fuel Valve, as shown on Figure 5-3a, 5-3b and 5-3c, above.

4. It may be necessary to jump out the High Gas Pressure switch.

5. Set the ON/OFF switch to the

position to start the unit.

6. The unit should purge and light the Pilot flame and then shut down after reaching the main

Burner Ignition cycle and display

FLAME LOSS DURING IGN

7. Open the valve previously closed in step 3 and press the

CLEAR

button.

8. Restart the unit and allow it to prove flame.

9. Once flame is proven, close the manual gas valve located between the SSOV and the

Air/Fuel Valve (see Figure 5-3a, 5-3b or 5-3c, above).

10. The unit should shut down and do one of the following:

BMK 2500 & 3000 units

: the unit will Lockout and

FLDR

(

Flame Loss During Run

)

will flash in the display.

BMK 750

– 2000 units

: the unit will execute an

IGNITION RETRY

cycle by

performing the following steps:

•

The unit will execute a shutdown purge cycle for a period of 15 seconds and

display

WAIT FAULT PURGE

•

The unit will execute a 30 second re-ignition delay and display

WAIT RETRY

PAUSE

•

The unit will then execute a standard ignition sequence and display

WAIT

IGNITION RETRY

•

Since the manual gas shutoff valve is still closed, the unit will fail the ignition

retry sequence. Therefore it will shut down and display

FLAME LOSS DURING

IGN

following the

IGNITION RETRY

cycle.

11. Open the valve closed in step 9.

12. Press the

CLEAR

button. The unit should restart and fire

Содержание Aerco Benchmark OMM-0116































































































































Результаты поиска

Содержание Aerco Benchmark OMM-0116

Отзывы:

Похожие инструкции для Aerco Benchmark OMM-0116

Бренды по названию

Популярные бренды

Watts Aerco Benchmark OMM-0116, Руководство по установке и запуску

Результаты поиска

Содержание Aerco Benchmark OMM-0116

Отзывы:

Похожие инструкции для Aerco Benchmark OMM-0116

Бренды по названию

Популярные бренды