Watts Aerco Benchmark OMM-0116 Скачать руководство пользователя страница 106

Страница: 106 / 126

Benchmark 750-3000 Installation & Startup Manual

SECTION 6

– BOILER SEQUENCING TECHNOLOGY

OMM-115_D

•

GF-200

•

5/9/2019

Technical Support

•

(800) 526-0288

•

Mon-Fri, 8 am - 5 pm EST Page 106 of

126

OPTION 4 - Outdoor Reset With Modbus Header Sensor And Modbus
Outdoor Sensor Instructions

NOTES:

•

Polarity must be observed for the RS485 connections. The ground for the shield is at

the “SHLD” terminal in the I/O the Box.

•

When mounting the Outdoor sensor, it must be located on the North side of the building

where an average outside air temperature is expected. The sensor must be shielded
from direct sunlight as well as impingement by the elements. The outdoor sensor may
be wired up to 200 feet (61m) from the boiler.

•

There is no polarity to be observed. The ground for the shield is at the power supply

ground. The sensor end of the shield must be left free and ungrounded.

Step 3 - Configure ALL C-More Units

On ALL Boilers:

1. Go to the

Configuration

menu and set the BST Menu item to

Enabled

2. Go to the Boiler Sequencing Menu and set the BST Mode item to

BST Client

(for now).

On MANAGER only:

3. Go to the BST Setpoint item and enter the Failsafe Setpoint.

4. Go to the BST Setup Menu item and set to

Enabled

5. Go to the BST Setpoint Mode item and select

Outdoor Reset

6. Go to the Head Temp Source item and select

Network

7. Go to the Header Temp Addr item and enter the Modbus Address (240).
8. Go to the Header Temp Point item and enter the Modbus Point (14).

9. Go to the BST Outdoor Sens item and select

Enabled

10. Go to the Outdoor Temp Source item and select

Network

11. Go to the Outdoor Temp Addr item and enter the Modbus Address (240).
12. Go to the Outdoor Temp Point item and enter the Modbus Point (15).

When ALL C-More units have been configured:

13. Go to the Boiler Sequencing Menu of the Manager unit and set the BST Mode item to

BST

MANAGER

TEMP SENSOR P/N

61043

MODBUS TRANSMITTER

I/O BOX

Содержание Aerco Benchmark OMM-0116































































































































Результаты поиска

Содержание Aerco Benchmark OMM-0116

Отзывы:

Похожие инструкции для Aerco Benchmark OMM-0116

Бренды по названию

Популярные бренды

Watts Aerco Benchmark OMM-0116, Руководство по установке и запуску

Результаты поиска

Содержание Aerco Benchmark OMM-0116

Отзывы:

Похожие инструкции для Aerco Benchmark OMM-0116

Бренды по названию

Популярные бренды