Watts Aerco Benchmark OMM-0116 Скачать руководство пользователя страница 50

Страница: 50 / 126

Benchmark 750-3000 Installation & Startup Manual

SECTION 3 - START SEQUENCE

OMM-115_D

•

GF-200

•

5/9/2019

Technical Support

•

(800) 526-0288

•

Mon-Fri, 8 am - 5 pm EST Page 50 of

126

Start Sequence:

The “Spark Cycle Time” item in the

Factory

menu can be set to either 0 Sec, 2 Sec or 7

Sec to define the duration of the Spark Element Cleaning Cycle. This cycle turns on the

spark transformer to produce a spark (with no gas flowing) to clean the spark element
of moisture or carbon buildup.

c) For the duration of this cycle, the C-More Controller will display the

CLEANING

IGNITER

message.

d) Following the Spark Element Cleaning Cycle, power is applied to the Gas Safety Shut-

off Valve (SSOV) and the C-More Controller displays the

PRE IGNITION

message.

When the SSOV indicates the Gas Valve is OPEN (POC), the C-More Controller
displays the

IGNITION TRIAL

message.

e) If no spark is present 3 seconds into the IGNITION TRIAL, the C-More Controller will

abort the Ignition Cycle and shut down the boiler. Refer to Section 6:

Troubleshooting

Guide

in the

Benchmark 750

– 3000 Operation and Maintenance Guide

OMM-0116

(GF-201) for guidance if this occurs.

Figure 3-4: Air/Fuel Valve In Ignition Position

6. Up to 4 seconds will be allowed for ignition to be detected. The igniter relay will be turned

off one second after flame is detected.

7. After 2 seconds of continuous flame,

FLAME PROVEN

will be displayed and the flame

strength will be indicated. After 5 seconds, the current date and time will be displayed in
place of the flame strength.

8. With the unit firing properly, it will be controlled by the temperature controller circuitry. The

boiler’s

VALVE POSITION

will be continuously displayed on the front panel bargraph.

9. Once the demand for heat has been satisfied, the C-More Controller will turn off the SSOV

gas valve. The blower relay will be deactivated and the Air/Fuel Valve will be closed.

STANDBY

will be displayed.

TO BLOWER

AIR IN

IGNITION

VALVE POSITION

DIAL AT

25% to 35%

STEPPER
MOTOR

Содержание Aerco Benchmark OMM-0116































































































































Результаты поиска

Содержание Aerco Benchmark OMM-0116

Отзывы:

Похожие инструкции для Aerco Benchmark OMM-0116

Бренды по названию

Популярные бренды

Watts Aerco Benchmark OMM-0116, Руководство по установке и запуску

Результаты поиска

Содержание Aerco Benchmark OMM-0116

Отзывы:

Похожие инструкции для Aerco Benchmark OMM-0116

Бренды по названию

Популярные бренды