background image

21

 

 

                                                                                                                                                   

                                                                                                                                         

Service Instructions / Instructional Videos Available at www.watersoftinc.com

A. 

General Preliminary Instructions 

 

PERFORM BEFORE ALL SERVICING OPERATIONS

 

1. Turn off water supply to conditioner.

 

    -If the conditioner installation has a “three valve” bypass system, first open the valve in the  

 

     bypass line, then close the valves at the conditioner inlet and outlet.

 

    -If the conditioner has an integral bypass valve, put it in the bypass position.

  

    -If there is only a shut off valve near the conditioner inlet, close it.

 

2. Relieve water pressure in the conditioner by stepping the control into the backwash position mo

                  mentarily. Return the control to the service position.

 

3. Unplug electrical cord from outlet.

B. 

To Replace Injectors & Screen 

 

1. Follow steps 

A1 - A3 

(above)

 

2. Remove injector cap screws and remove cap. 

 

3. Remove injector assembly. Apply silicone lubricant to new injector assembly O rings and install.  

 

    Be sure to push injector assembly tightly so O rings are seated. Install a new screen.

 

4. Apply silicone lubricant to new gasket and install on injector cap.

 

5. Follow 

D7 - D14.

C. 

To Replace Powerhead

 

1. Remove the control valve cover and disconnect the power supply.

 

2. Disconnect the meter cable from circuit board and feed back through control (if existing meter is

                  being re-used)

 

3. Remove screw and washer at drive yoke. Remove powerhead mounting screws. The entire pow

                  erhead assembly will now lift off easily.

 

4. Put new powerhead on top of the valve. Be sure the drive pin on main gear engages slot in drive 

                  yoke (wide side of drive yoke upright must face to the left away from the motor).

 

5. Replace powerhead mounting screws. Replace screw and washer at drive yoke.

 

6. Reconnect meter signal, optical sensor, power supply, and circuit board signal wires.

 

7. Reinstall top cover.

D.

 

To Replace Brine Valve

 

1

.   

Follow steps 

A1 - A3

 

2.   Remove the top cover. Disconnect the meter cable from the meter assembly.

 

3.   Remove screw and washer at piston drive yoke. Remove powerhead mounting  screws. The en

                    tire powerhead assembly will now lift off easily.

 

4.   Remove piston retaining plate screws and pull upward on end of piston yoke until assembly is 

                    out of valve.

 

5.   Pull brine valve from valve body.

 

6.   Apply silicone lubricant to O ring on new brine valve assembly and press into brine valve hole, 

                    shoulder on bushing should be flush with injector body.

 

7.   Reinstall piston and powerhead assembly.

 

8.   Reconnect brine tube and drain line.

 

9.   Return bypass or inlet valving to normal service position. Water pressure should now be applied 

                    to the conditioner, and any bypass line shut off.

 

10. Check for leaks at all seal areas. Check drain seal with the control in the backwash position.

 

11. Plug electrical cord into outlet.

 

12. Set time of day and cycle control valve manually to assure proper function. Make sure control 

                    valve is returned to the service position.

 

13. Make sure there is enough salt in the brine tank.

 

14. Start regeneration cycle manually if water is hard.

 

15. Replace control valve cover. 

Содержание CD24





























Отзывы: