background image

11

 

 

                                                                                                                                                   

                                                                                                                                         

- Final Check -

1. Be certain the bypass valve is in the SERVICE position.

2. Make sure the power supply is connected to an uninterrupted 115-volt outlet.

3. Check that the time of day is set

4. Double check regeneration schedule.

5. Make final check for leaks!

6. Fill out warranty card online at www.watersoftinc.com 

7. Leave all manuals with unit.

- Operation, Care and Cleaning -

When the bypass valve is in the SERVICE position (position of bypass lever is parallel to the inlet / outlet 

piping), water is directed through the water softener. Water may be bypassed by turning the lever to the 

bypass position (position of bypass lever is at right angles to inlet / outlet piping). Water to the home will 

bypass the softener and be untreated.

You should manually bypass the softener if :

1. The outside lines do not bypass the water softener and water is to be used for lawn sprinkling or other 

similar uses.

2. Servicing the water softener.

3. A water leak from the water softener is evident.

4. Shock treating water well and piping with chlorine or other disinfectant.

- General Care and Cleaning -

1. Do not place heavy or sharp objects on water softener or cabinet.

2. Use only mild soap and warm water to clean exterior of the unit. Never use harsh, abrasive cleaners.

3. Protect the water softener and drain line from freezing.

4. Reset time for daylight saving time periods.

5. Inspect and clean the brine tank when sediment appears in the bottom of the salt compartment.

6. Always keep the brine tank supplied with good quality salt, a type designed for use in water softeners.

Start Up Procedure

Содержание CD24





























Отзывы: