background image

 

 

 

4

 

Important Safety Information 

WARNING 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: 

1.

 

Installation of the INSTA-80 must be carried out in accordance with these 

instructions, and must be conducted by competent personnel. 

2.

 

The electrical installation must comply with BS7671 (commonly referred 

to as the IEE Wiring Regulations) and all relevant building regulations, or 
any particular regulation or practice specified by the local electricity 

supply company. 

3.

 

This appliance must be earthed. All supplementary Bonding must 
comply with BS7671 

4.

 

This product is suitable for installation in zone 2 and is IPX4 rated. 

5.

 

The plumbing installation must comply with all national or local water 

regulations and all relevant building regulations, or any particular 
regulation or practice specified by the local water supply company. 

6.

 

The INSTA-80 is intended to be permanently connected to the fixed 
electrical wiring of the mains system. A separate supply must be provided 

from the consumer unit to the INSTA-80. 

7.

 

Isolate the electrical and water supplies before commencing installation. 

The electricity must be switched off at the consumer unit and the 
appropriate circuit fuse removed, if applicable. 

8.

 

The INSTA-80 must be provided with means for disconnection that is 
incorporated into the fixed wiring in accordance with the relevant local 

wiring regulations. The isolating switch must be local to the appliance. 

9.

 

A 25mA Miniature Circuit Breaker (MCB) must be fitted. This may be part 
of the consumer unit or a separate unit. 

10.

 

Ensure all electrical connections are tight, to prevent overheating. 

11.

 

The INSTA80 must not be fitted where it may be exposed to freezing 

conditions. Ensure that any pipe-work that could become frozen is 
properly insulated. 

12.

 

The INSTA-80 must not be fitted to a heated water supply. 

13.

 

The INSTA-80 is not suitable for areas with high humidity or temperature 

(i.e. steam rooms and saunas). 

14.

 

The INSTA-80 has inbuilt electrical connections and should never be 

tampered with, only a competent person should remove the cover. We 
recommend any maintenance work is carried out by a Watersave Service 

Содержание INSTA-80

















Отзывы: