WaterLogic WL800 - MAX II Скачать руководство пользователя страница 65

Страница: 65 / 75

Chilling and Service LED Alternate Blinking – Full Water Level Error

Possible Reason

Solution

Low Level and Overflow

Sensors indicted water but full

level sensor is not detected

Check connection to low water level sensor.

Replace full water level sensor

Heating, Chilling and Service LED Sequentially Blink

Possible Reason

Solution

Overflow sensor has detected

water but neither low or full

sensors are detected

Check connections to both low and full water sensors.

Replace both Low Water and Full Water Sensors

Heating, Chilling and Service LED Blinks Simultaneously

Possible Reason

Solution

All three level sensors have

detected water

Check Feed Valve for Debris.

Clean or replace feed valve.

Service LED is On – Leak Detection Probe has detected water

Possible Reason

Solution

Dry inside of unit and leak

detector.

Check unit for leak and repair or replace faulty parts.

WL800

Operating, Installation, and Service Manual Page 65 - Revision: 5-14-2015

Содержание WL800 - MAX II












































































Результаты поиска

Содержание WL800 - MAX II

Отзывы:

Похожие инструкции для WL800 - MAX II

Бренды по названию

Популярные бренды

WaterLogic WL800 - MAX II, Руководство по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание WL800 - MAX II

Отзывы:

Похожие инструкции для WL800 - MAX II

Бренды по названию

Популярные бренды