background image

Page 29

 

WATERAX 

STRIKER-2/3 Owner's Manual   

04/2015 

 

 

29 

Warranty 

 

WHEREAS 

subject to the following general and specific terms and conditions, 

WATERAX Inc. (the “

Seller”) hereby warrants to the 

original purchaser of the products from 

WATERAX, (the “

Purchaser”) that its products, including any pump parts products manufactured 

by 

WATERAX (the “

Products”) sold under Seller’s brands will be free of defects in material and workmanship for the applicable Warranty 

Period (as set out in full at www.waterax.com/eng/warranty). 

 

Product 

Warranty Period 

Coverage 

4-Stroke Powered Pumps 

Two (2) Years 

Limited 

2-Stroke Powered Pumps 

Earlier of One (1) Year or 

One hundred (100) run hours 

Limited 

Backpack Pumps 

One (1) Year 

Limited 

Skid Units 

One (1) Year 

Limited 

Control Panels, Electronics Manifolds 

One (1) Year 

Limited 

Genuine Parts 

Ninety (90) Days 

Limited 

 

1.  Limitations, exclusions and other terms and conditions applicable for all Products: 

a.   The Warranty shall be voided upon the occurrence of any of the following events: (a) the Product is used for an application, with 

products or in a manner other than the application, products and manner for which such Product is designed and intended; (b) the 

Product is subjected to a use, service, condition or environment other than a use, service, condition or environment for whic h such 

Product is designed and intended; (c) the Product is not properly installed by the Purchaser or its agent or representative; (d) the 

Product is not properly tested and maintained in accordance with Seller’s product manuals and supplemental instructions and 

guidelines, applicable industry standards and guidelines, and applicable legal and regulatory requirements; (e) the Product is 

altered, modified, serviced (with the exception of routine maintenance performed in accordance with the Seller’s product manu

als 

and supplemental instructions as set out in full at www.waterax.com/eng/warranty, and industry accepted standards and 

guidelines), or repaired by a person other than the Seller or a person authorized by the Seller to make such alteration or 

modification or perform such service or repair; (f) the Seller is not paid the full amount of the purchase price for the Product when 

due; (g) any bad faith invocation of a warranty claim or breach of a purchase agreement by the Purchaser.  

 

b.   The following are excluded from Warranty coverage: (a) non-defective parts worn, exhausted or consumed through normal usage 

of the Product; (b) any consumable parts normally subject to routine replacement, including but not limited to pump packing, O-

rings, gaskets, intake screens, anodes or filters; (c) routine maintenance as specified and in accordance with the Seller’s p

roduct 

manuals and supplemental instructions and guidelines as set out in full at www.waterax.com/eng/warranty; (d) failure due to 

compliance with a specification or design provided or required by Purchaser; (e) failure due to improper operation, excess 

pressure, excess voltage, abuse, misuse, negligence or accidents or other similar causes; (f) failure due to operator error; (g) 

damage during or after shipment and failure attributable thereto or resulting there from; (h) failure attributable to or resulting from 

the failure or substandard, inadequate or improper performance of any part, component or equipment not supplied by the Seller; 

(i) failure attributable to or resulting from the failure or substandard, inadequate or improper performance of any third party part, 

component, product or equipment, whether or not combined, packaged, incorporated, installed or used with a Seller brand part, 

component, product or equipment.  

 

2.   Claim Procedure. 

The claim procedure applicable under this warranty, including any applicable notice and documentation 

requirements, are set out in full at www.waterax.com/eng/warranty and constitute an essential term of this Warranty.  

 

3.  Repaired and Replacement Product. 

If requested to do so by the Purchaser the Seller may, at its sole option and in its  sole 

discretion, supply a replacement Product or part to the Purchaser prior to making a final determination as to whether Warranty 

Coverage is available. 

 

If the Seller ultimately determines that no Warranty Coverage is available for a Product claimed to be defective, the Purchas er shall 

have the option of either (a) having the Product returned to it freight collect without repair or replacement; or (b) if Seller determines 

that the Product is repairable, have the Product repaired by Seller or another party designated by it on a time and materials basis at 

Seller’s then current standard charges for non

-warranty repairs and then returned to Purchaser freight collect. The Seller reserves the 

right to use reconditioned parts for Warranty repairs and to use reconditioned Products for Warranty replacements. Repaired Product 

and replacement Product shall be warranted only for the remainder of the original Warranty Period.  

 

 

4.  Limitation of Liability: SELLER’S WARRANTY AS SET FORTH HEREIN IS SELLER’S SOLE AND EXCLUSIVE WARRANTY AND 

IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ALL WARRANTIES OF 

MERCHANTABILITY, QUALITY, COURSE OF DEALING, USAGE OF TRADE, FITNESS FOR A PARTICULAR PURPOSE AND 

NON-INFRINGEMENT. THE RIGHTS AND REMEDIES SET FORTH HEREIN ARE THE SOLE AND EXCLUSIVE RIGHTS AND 

REMEDIES AGAINST SELLER, EXCEPT FOR THE SPECIFIC LIABILITIES AND OBLIGATIONS PROVIDED HEREIN, SELLER 

SHALL HAVE NO LIABILITY OR OBLIGATION WITH RESPECT TO ANY PRODUCT CLAIMED TO BE DEFECTIVE IN ANY 

MANNER.

 

Содержание STRIKER-II Series

































Отзывы: