MODEL WPMZ-3-□□□-□□-□□□
9/12
IM-0881-04
１３－４.
PEAK VALUE HOLD FUNCTION
This is a function which holds the maximum display value.
PeakHold A
：
holds the maximum display value of Ach
PeakHold B
：
holds the maximum display value of Bch
PeakHold A&B
：
holds the maximum display value of
Ach and Bch
１３－５.
BOTTOM VALUE HOLD FUNCTION
This is a function which holds the minimum display value.
*
When both of the maximum value hold and the minimum value
hold are ON simultaneously, only the maximum value hold
becomes valid.
Minimum hold A
：
holds the minimum display value of Ach
Minimum hold B
：
holds the minimum display value of Bch
Minimum hold A&B
：
holds the minimum display value of Ach
and Bch
１３－６.
AMP HOLD FUNCTION
This is a function which holds the difference between maximum
and minimum.
AmpHold A
：
holds that of Ach
AmpHold B
：
holds that of Bch
AmpHold A&B
：
holds that of Ach and Bch
１３－７.
DEVIATION HOLD FUNCTION
This is a function which holds display value that has the
maximum absolute value of difference from reference value.
DevHold A
：
holds that of Ach
DevHold B
：
holds that of Bch
DevHold A&B
：
holds that of Ach and Bch
１３－８.
AVERAGE HOLD FUNCTION
This is a function which holds average value of display value.
AveHold A
：
holds that of Ach
AveHold B
：
holds that of Bch
AveHold A&B
：
holds that of Ach and Bch
１３－９.
DIGITAL ZERO FUNCTION
This is a function which makes display value “0” as offset.
DigitalZeroA
：
Execute to Ach.
DigitalZeroB
：
Execute to Bch.
DigitalZeroA&B
：
Execute to both Ach and Bch.
１３－１０.
PATTERN SELECT FUNCTION
The pattern select function is the function which switches the
pattern number to use for measurement. By using pattern select
1-3, Up to 8 patterns can be switched.
Function
Name
Selected pattern No.
（
pattern No. in use
）
1
2
3
4
5
6
7
8
Pattern
select1
Open
Short
Open
Short
Open
Short
Open
Short
Pattern
select2
Open
Open
Short
Short
Open
Open
Short
Short
Pattern
select3
Open
Open
Open
Open
Short
Short
Short
Short
Open
：
pattern select terminal is open or connected to “1” level.
Short: pattern select terminal is shorted to COM terminal or
connected to “0” level.
１３－１１.
DISPLAY CHANGE FUNCTION
The display change function is the function which switches
display and performs same action of DISP key.
１３－１２.
TREND LOG FUNCTION
Trend log function is to acquire the alarm log any time by
external control It is a function to execute with. While data is
being acquired, the trend screen displays the clock mark The
icon will light up.
１３－１３.
WAVE COMPARE FUNCTION
This is a function which start/stop wave comparison.
WaveCompA
：
Order that of Ach.
WaveCompB
：
Order that of Bch.
１３－１４.
MULTI HOLD FUNCTION
This is a function which start/section switch/stop multi hold.
MultiHoldA
：
Order that of Ach.
MultiHoldB
：
Order that of Bch.
１４.
SHORTCUT FUNCTION
External control functions are registered to arrow keys and are
performed not by the terminal control but by the operation of the
keys
１４－１.
REGISTERING SHORTCUTS
External control functions which would be performed by
shortcuts are assigned to arrow keys by the following steps.
These functions below are registered by default.
・
1ch product
Key
Default function
AutoAdjustA *
None
DigitalZeroA
ManuAdjustA *
*Only for straingauge input
・
2ch product
Key
Default function
AutoAdjustA
※
AutoAdjustB
※
DigitalZeroA
DigitalZeroB
*Only for straingauge input
１４－２.
PERFORMING SHORTCUTS
A shortcut function is performed by holding down the arrow key
which an external control function is registered for 1 second.
An active function becomes inactive by holding down the arrow
key which the function is registered for 1 second.
１５.
MEASURE MODE
Select measure mode
(Setting)→4.System→MeasureMode
Setting
：
Default/MultiHold/WaveCompare
１５－１.
Default
Perform normal measurement.
１５－２.
Multi hold
In the multi hold mode, measurements are divided into four
sections of section 1 to section 4, arbitrary hold settings are set
to each section, and comparison output is performed by hold
value in each section and comparison judgment value set for
each section, respectively.
Parameter
1st Layer
2nd Layer
3rd Layer
1.Input
MultiA Base
MultiB Base
PatternSelect
SectionSwitch
SectionTimerS1
～
S4
CompleteOutput
AlarmColorS1
～
S4
MultiA
S1
～
S4
MultiB
S1
～
S4
PatternSelect
HoldStartCond.
Threshold
ThresholdOnDir
ThresholdTimeout
TimeoutOutput
DelayTimer
HoldType
DevBaseValue
DifValue
DifMag
InfTimeA
InfTimeB
InfValueZ
CompOutput
CompAlarmCond.
CompJudgeValue
CompTiming
NoDetected
3.Display
DispSelect
MultiSelect
For detail and how to use this mode, please refer to the
detailed manual which can be downloaded from our home page.
