MODEL WPMZ-3-□□□-□□-□□□
8/12
IM-0881-04
１０－１.
LOCATIONS OF PARAMETERS FOR UNIT SETTINS
1st Layer
2nd Layer
3rd Layer
1.Input
StrainInputA
StrainInputB
ProcessInputA
ProcessInputB
DispUnit
Calc
DispUnit
１０－２.
AVAILABLE UNITS
You can set these 20 units below.
Units
μm,mm,cm,m,g,kg,N,kN,MN,Pa,kPa,MPa,hPa,
kg/m
2
,N/m
2
,t,inch,mN
・
m,N
・
m,kN
・
m
１１.
DispSelect
Select the screen to be displayed as measurement screen. When
some screens are set, they are displayed in turn each time the
DISP key is pressed.
Locations of parameter for
DispSelect
1st Layer
2nd Layer
3rd Layer
3.Display
DispSelect
MeasureSelect
LevelSelect
TrendSelect
WaveSelect
MultiSelect
*
WaveSelect is active when measure mode is wave compare, and
MultiSelect is active when measure mode is multi hold
DISP
DISP
DISP
Measurement Display
DISP
*Example: Measurement display (calculation), measurement
display (Ach + comparison), level display (Ach + Bch), trend
display (Ach + Bch)
１２.
COMPARATIVE OUTPUT FUNCTION
Settings of comparative output functions needs 10 parameters to
set for each output.
The following describe only main setting parameters and refer to
detailed manual which can be downloaded from our homepage
for other parameters.
１２－１.
Locations of parameter for
comparative output
1st Layer
2nd Layer
3rd Layer
4.Output
CompareAL1
CompareAL2
CompareAL3
CompareAL4
PatternSelect
OutputDispValue
ActCondition
ComparedMode
OnConditions
ThresholdOnDelay
OffDelay
OutputMode
OutputLogic
OnBgColors
*Refer to “
7. SETTING LAYER OVERVIEW
”
１２－２.
OutputDispValue
Comparative outputs AL1-AL4 are settable independently and
they have no magnitude relationship.
For example, measured value of Ach is assigned to AL1,
measured value of Bch is assigned to AL2 and calculate value is
assigned to AL3, AL4 and so on. Every display item can be freely
assigned to comparative outputs.
１２－３.
COMPARISON JUDGEMENT VALUE
The comparison judgement value is a threshold value to judge.
How to set the value is shown below.
*The following is an explanation for the compare mode of “Level
judgement”.
(Setting)→2.Output→CompareAL1→Threshold
Set value with
arrow keys
Press Enter key to edit value
4
th
Layer
4
th
Layer
4
th
Layer
4
th
Layer
3
rd
Layer
Back to
3rd Layer
Press Enter key to determine
Finish
●
Level judgement action
Comparative
Output
Comparison
type
Comparison
formula
judgement
result
AL1
alarm when
over
display value
＞
AL1
judgement value
AL1 ON
AL2
alarm when
over
display value
＞
AL2
judgement value
AL2 ON
AL3
alarm when
under
display value
＜
AL3
judgement value
AL3 ON
AL4
alarm when
under
display value
＜
AL4
judgement value
AL4 ON
*Refer to
“
16. SPECIFICATIONS –output specifications [comparative
output]
”
１３.
EXTERNAL CONTROL FUNCTION
As external control functions, the WPMZ has comparative
output reset function, total reset function, measurement inhibit
function, display hold function, maximum value hold function,
minimum value hold function, digital zero function and pattern
select function, each function can be executed by assigning to
external control terminal 1 to 5.
*External control functions are also assigned (entered) to 4
arrow keys as shortcut functions.
１３－１.
COMPARE RESET FUNCTION
This is a function that makes all of comparative judgement
results and their outputs OFF.
１３－２.
HOLD RESET FUNCTION
This is a function that reset hold state.
HoldResetA
：
Reset hold state of Ach
HoldResetB
：
Reset hold state of Bch
HoldResetA&B
：
Reset hold state of Ach and Bch
１３－３.
DISPLAY HOLD FUNCTION
Display hold function holds display value. While this function is
valid, measurement action is performed internally and the latest
measurement value is displayed when the function become
invalid.
Disp
Ho
ld A
：
holds the display of Ach
DispHold B
：
holds the display of Bch
DispHold A&B
：
holds the display of Ach and Bch
AL1 Hysteresis
Display value
AL1 Judgement value（Over）
AL2 Hysteresis
AL2 Judgement value（Over）
AL3 Hysteresis
AL3 Judgement value（Under）
AL4 Hysteresis
AL4 Judgement value（Under）
AL2
AL1
AL3
AL4
J
ud
ge
m
en
t
re
su
lt
