background image

Warren Elevating 5

th

 Wheel 

CAUTION:

 Before operating or before performing any service or maintenance on this 

Warren Product, all appropriate OSHA regulations must be observed. 

 
Safety Notice 

Proper service and repair are important to the safe, reliable, operation of Warren’s 
products. Operation and servicing procedure recommended by Warren are in this manual 
and are effective for proper use of this product. Some of these operations may require the 
use of tools or blocking devices specifically designed for the purpose. Special tools 
should be used when and as recommended. It is important to note that warnings against 
the use of specific operations or methods that can damage the product or render it unsafe 
are stated in this manual. It is also important to understand these warnings are not 
exhaustive. Warren could not possibly know, evaluate, and advise the service trade of all 
conceivable ways in which operation or service might be done or of the possible 
hazardous consequences of each way. Accordingly, anyone who uses operational 
procedure, service procedures, or tools whether recommended by Warren or not, must 
first satisfy himself thoroughly that neither his safety nor the product safety will be 
compromised or jeopardized by the selected procedure. 

Preface 

 
This Operation and Maintenance Manual is to assist in the correct operation and 
maintenance of the Warren Elevating 5

th

 wheels by providing information for installation, 

operation, service, and maintenance. Please read this manual thoroughly before 
proceeding to use the equipment. 
 
The economic life of any piece of equipment is directly related to the care and 
maintenance it receives. Use this manual as a reference in seeing that this unit receives 
proper care and is correctly operated. 
 
The use of genuine Warren parts is recommended for best equipment service as well as 
insuring that our warranty policy is not voided. 
 
If additional information is required or should you desire to have a qualified service 
facility work on this unit, contact your local Warren Distributor. 
 

Name __________________________________________ 
Address ________________________________________ 
_______________________________________________ 
Phone __________________________________________ 
Fax ____________________________________________ 

 
Warren reserves the right to make changes in our units at anytime without incurring any 
obligation whatsoever to change units already in the field. 
 

Содержание FW-30










































Отзывы: