background image

South Bend, Indiana USA 

 |

  networketi.com

PT-SINGLE

 INSTALLATION MANUAL  |  PART NO. 

25166

 REV 

D

12

CONTACTING CUSTOMER SERVICE

For assistance, contact Customer Service. Office hours are 

from 8:00 AM until 5:00 PM ET.

Email:

 

[email protected]

Web:

  

warmlyyours.com

RETURNS AND REPLACEMENT PART PURCHASES

Equipment cannot be returned for credit once it has 

been installed. ETI will repair or replace faulty equip-

ment under warranty. Prior to removal of equipment for 

warranty return, please contact ETI Technical Support for 

troubleshooting assistance.
Before returning a unit to ETI, obtain a Return Merchandise 

Authorization  from  our  Customer  Service  Department, 

available between 8:00 a.m. and 5:00 p.m. Eastern Time. If 

possible, use the original container and packing materials 

when packing the unit for shipment. It is important to 

mark  the  Return  Merchandise  Authorization  clearly 

on the outside of the shipping container so that it may 

be correctly processed upon receipt at Environmental 

Technology. For more information about replacement 

parts or for a replacement Data Sheet or Manual, please 

visit www.networketi.com.

LIMITED WARRANTY

ETI’s two year limited warranty covering defects in 

workmanship and materials applies. Contact Customer 

Service for complete warranty information.

DISCLAIMER

ETI makes no representations or warranties, either 

expressed or implied, with respect to the contents 

of this publication or the products that it describes, 

and  specifically  disclaims  any  implied  warranties  of 

merchantability or fitness for any particular purpose. ETI 

reserves the right to revise this publication, and to make 

changes and improvements to the products described 

in this publication, without the obligation of ETI to notify 

any person or organization of such revisions, changes or 

improvements.

Copyright © 2019 ETI,

®

 All rights reserved.

Содержание TRACON PT-SINGLE













Отзывы: