background image

South Bend, Indiana USA 

 |

  networketi.com

PT-SINGLE

 INSTALLATION MANUAL  |  PART NO. 

25166

 REV 

D

2

instructions contained in this manual and those provided 

by the heater manufacturer.

Size  the  circuit  breaker  appropriately  for  the  expected 

load  and  inrush  current.  The  maximum  rated  current 

for the 

PT-SINGLE

 is 30 amps with resistive load.

Heater loads and their controls should not share a circuit 

branch with other types of equipment. A shared circuit 

may result in electromagnetic interference that can affect 

system operation.

Make certain that the heater shield is properly grounded. 

Failure to do so may result in damage to the equipment 

or fire.

Following installation and prior to beginning system 

operation, refer to and perform the Post-Installation Test 

described in this manual.

ITEMS INCLUDED

QTY. 

P/N 

DESCRIPTION

25170 

TRACON MODEL 

PT-SINGLE

  

Single-Point General Purpose 

Heat–Trace Control

25076 

Temperature Sensor

25299 

PT-SINGLE

 Installation Sheet

OVERVIEW

The  TRACON 

PT-SINGLE

  Heat–Trace  Control  is  a  single–

point  microprocessor–based  heat–trace  control 

thermostat.  It  is  ideal  for  applications  which  require 

Ground–Fault 

Equipment  Protection  (GFEP).  Ideal  uses 

include  freeze 

protection,  hot  water  temperature 

maintenance,  grease  line  trace,  tank  heating,  and  other 

temperature monitoring and control applications. The 

PT-

SINGLE

 and its heater load can operate with an available 

line voltage source of 100 –

 

277 V ac. The controller and 

heater  load  share  the  same

 

supply  connection.  The 

internal load contactor is rated to

South Bend, Indiana USA 

 |

  networketi.com

switch up to 30 A resistive. The Integral GFEP provides 

safety in compliance with national and local electrical 

codes. The unit’s housing is a NEMA 4X IP66 weather–

resistant enclosure for enhanced durability.

FEATURES AND BENEFITS

•  Adjustable temperature setpoint allows precise control

of a wide range of processes

•  Can use an NEC Class 2 temperature sensor with up to

2,000 ft. cable for enhanced installation options

•  Thermistor temperature sensor with 20 ft. cable included

for applications of −40 °F to 230 °F (−40 °C to 110 °C)

• RTD input allows higher accuracy and extreme–

temperature applications

•  The unit can accommodate RTD sensors with 3–wire

configuration

• Temperature display for accurate adjusting and

monitoring

• Load current display for accurate adjusting and

monitoring

• Ground fault current display for accurate monitoring,

protection, and alarm

• Adjustable alarm thresholds for excess ground fault

current, load current, and temperature

• Alarms indicated with panel display and relay contact

for remote signaling

• A Fault Mode setting which can be set to energize or de-

energize the heaters during a sensor failure

• Fire Protection Mode maintains heater operation for use

in critical fire protection systems

• Durable weather–resistant NEMA 4X IP66 enclosure

permits indoor or outdoor installation

The 

PT-SINGLE

 is permanently connected equipment 

and does not have an internal disconnect device. The

 

installer must provide an accessible disconnect device, 

with short circuit and overcurrent protection (these are

 

not supplied by Environmental Technology Inc). When 

power is applied, the system will start.

Содержание TRACON PT-SINGLE













Отзывы: