Page
Once you perform the three bell operations after applying power
,
the bell will shut off
automatically and you will hear
"
Enter Programming
"
and the
Headlight
and Reverse Lights will
flash alternately off and on.
Scrolling through the Program
Options
•
After entering programming
,
you will hear an announcement of the first Program
Option,
"
Option
1 - System Volume
".
•
To access other Program Options, simply flip the direction switch to the opposite
position and leave it there. Listen as each option number is announced in order
.
•
Flip the switch back and leave
it
there when you wish to stop at a particular option. After
you stop at an option you will hear the option number and name announced
.
When you
are scrolling through and stopping at Program Options
,
you are not making any
changes.
To make changes you must actually
enter
the Program
Option
.
Note:
If you accidentally go to a higher option number other than
the
one
you
wanted, simply turn
the power off
,
re-enter programming and start again.
Once
you reach the last
Program Option
,
it
will continue to announce the last option number.
Entering
a Program Option and Making Changes
After the verbal announcement of a Program
Option
,
you can enter that option by performing a
Slow
or
Quick
flip-and-back operation of the direction switch
.
Upon entering a Program
Option
,
you will hear the current setting for that option. For unused Program Options, you will hear
"Reserved".
For any volume option
,
you will hear
"Volume
equals X" {where
"X"
is its current
volume level setting). After a moment, you will hear the sound playing at its current volume
16
.
Note:
Entering a Program Option does not change the settings for that option
;
it only provides
information about its current value. After entering the
Program
Option, additional
Slow
or
Quick
flip and-back operations will program new settings as described in the above table. For all level
adjustments
,
a
Quick
operation will decrease one level while a
Slow
operation will increase one
level.
Note:
Since
"System
Volume
"
is the first
Program
Option
,
you can use
Quick
or
Slow
operations
immediately after entering programming to change the system volume.
Moving on to Other Program Options or Leaving Programming
•
Flip the direction switch at any time to the opposite position, and leave it there.
Quantum will first return to and announce the current program option and then
automatically advance to onto higher options.
•
Exit
Programming
any time
you
want by turning the power off and back on again.
Example 1: Setting Throttle Mode (Program Option# 10)
This will
determine
whether
your locomotive
uses Regulated Throttle
Control
(RTC) or Standard
Throttle
Control
(STC)
.
•
Enter
Programming
after powering up your
engine
by turning the bell on
,
then off and
then on as described above.
•
After
the
"Enter
Programming" followed by
"Option
One
-
System
Volume"
announcement of
the
first Program
Option
,
flip the direction switch and leave it
there.
You will hear
the announcement
"Option
1,
2, 3
..
.
etc
.
".
Stop
when you hear
"ten"
by
moving
the
direction switch back.
You
will hear
"Throttle
Mode".
•
Use
a
Slow
or
Quick
operation of the direction switch to enter
this option.
If
the
throttle
mode
is
at
its default value
(RTC), you will
hear
"
Mode
equals
Regulated;"
otherwise,
you will hear
"
Mode
equals Standard.
"
•
Use
a
Slow
or
Quick
operation
of
the
direction switch
to
change
the throttle mode
.
Repeated
Slow
or
Quick
operations
will
cause
the
throttle
mode
to alternate between
its two possible
values
(RTC,
STC, RTC
,
STC
...
etc
.
)
•
Once you have
selected
the
throttle mode
you wish
to use
,
turn the
throttle off.
When
you then
power
up
again,
your locomotive will
be
using the throttle
mode
you have just
selected.
Example 2: Setting V-Start (Program Option # 8)
This
will
determine
the voltage
(and
throttle
position)
where your
engine
will leave neutral
and
move
out.
•
Enter
Programming
after powering
up your
engine
by turning the bell
on,
then off
and
then
on as described above.
•
After
the
"Enter
Programming" followed by
"Option
One
-
System
Volume"
announcement
of
the first
Program
Option,
flip
the direction
switch and
leave
it
there.
You hear the
announcement
"Option
1
,
2, 3
...
etc
.".
Stop
when you
h
ear "eight"
by
moving the direction
switch back.
You will hear
"
V
-
Start"
.
•
Use
a
Slow
or
Quick
operation
of
the
direction
switch
to
enter
this
option.
You
will
hear
"V-Start
equals
X" where
"
X"
is the track voltage value
currently set to
leave
neutral
".
"Setting
any
volume in Analog will also
apply
t
oDCCand
vice-versa.
