manualshive.com logo in svg

Wallenstein WP245, Руководство оператора

Поделиться
Скачать
Wallenstein WP245 Скачать руководство пользователя страница 7

2.  Safety

2.1  Safety Alert Symbol

This Safety Alert Symbol means: 

ATTENTION! BE ALERT! 
YOUR SAFETY IS INVOLVED!

The Safety Alert Symbol identifies important safety messages 
on the Wallenstein Wood Processor and in the manual. 

When you see this symbol, be alert to the possibility of 
personal injury or death. Follow the instructions in the safety 
message.

2.2  Signal Words

The signal words 

DANGER

, 

WARNING

 and 

CAUTION

 determine 

the seriousness level of the warning messages in this manual. 
The appropriate signal word for each message in this manual 
has been selected using the following guidelines:

DANGER –

Indicates an imminently hazardous situation that, if not avoided, 

will

 result in death or serious injury. This signal word is to be 

limited to the most extreme situations typically for machine 
components which, for functional purposes, cannot be guarded.

WARNING –

Indicates a potentially hazardous situation that, if not avoided, 

could

 result in death or serious injury, and includes hazards that 

are exposed when guards are removed. It may also be used to 
alert against unsafe practices.

CAUTION –

Indicates a potentially hazardous situation that, if not avoided, 

may

 result in minor or moderate injury. It may also be used to 

alert against unsafe practices.

IMPORTANT

 – To avoid confusing equipment protection with 

personal safety messages, a signal word IMPORTANT indicates 
a situation that if not avoided, could result in damage to the 
machine.

2.3  Why SAFETY is Important

Three Big Reasons:

•  Accidents can disable and kill
•  Accidents can cause financial hardship
•  Accidents can be avoided

YOU

 are responsible for the SAFE operation and maintenance 

of your Wallenstein wood processor. 

YOU

 must ensure that 

you and anyone else who is going to use, maintain or work 
around the wood processor be familiar with the operating and 
maintenance procedures and related

 SAFETY 

information 

contained in this manual. This manual provides good safety 
practices that should be followed while using this machine. 

Remember, 

YOU 

are the key to safety. Good safety practices 

not only protect you but also the people around you. Make 
these practices a working part of your safety program. Be 
certain that 

EVERYONE

 using this equipment is familiar with 

the recommended operating and maintenance procedures 
and follows all the safety precautions. Most accidents can be 
prevented. 

Do not risk injury or death by ignoring good safety practices. 

2.4  Safety Rules

• 

It is the operator's responsibility to read, 
understand and follow ALL safety and 
operation instructions in this manual. If 
you do not understand any part of this 
manual and require assistance, contact 
your dealer, distributor, or Wallenstein 
Equipment.

 Safety

WP245 / WP275
3-Point Hitch Firewood Processor

Safety

7

Содержание WP245





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды