manualshive.com logo in svg

Wallenstein WP245, Руководство оператора

Поделиться
Скачать
Wallenstein WP245 Скачать руководство пользователя страница 28

6.4  Attaching Chain Saw to Holder

01158

2

3

4

1

5

Fig.  25 – 

Pivoting Chain Saw Holder

1.  Debris Chute
2.  Universal Chain Saw Adapter Plate
3.  Pivot Handle
4.  Chain Saw Guard
5.  Pivot Base

 CAUTION!

Review your chain saw manual for safe operating 

and handling procedures before beginning work.

 WARNING!

Do not attach a chain saw to the holder with a bar 

length longer than 30" (75 cm). The cutting chain 

could contact the push block or cylinder rod 

causing a hazardous situation. Injury or machine 

damage could result from flying debris.

IMPORTANT!  The chain saw must have dual bar-mounting 
studs to mount the chain saw adapter plate. Saws with 
captive guide bar nuts require them to be removed.

1. 

Remove the chain sprocket cover nuts from your chain 
saw. Some chain saws feature captive guide bar nuts in the 
chain sprocket cover. On these saws, replace the guide bar 
nuts with bushing spacers (2).

2. 

Thread the two bar mounting studs (3) onto the guide bar 
studs on your saw. 

3. 

Install the universal chain saw adapter plate (1) over the bar 
mounting studs.

01137

2

1

3

4

Fig.  26 – 

Universal Chain Saw Adapter Install

1.  Universal chain Saw Adapter
2.  Bushing Spacers
3.  Bar Mounting Studs
4.  Hex Bolts and Washers

4. 

Fasten everything together with the M8 x 20 mm hex bolts 
(4) and washers.

5. 

Slide the saw adapter plate into the guides on the chain saw 
pivot. Make sure the draw latch is open so the saw can 
slide in without interference. 

01138

Fig.  27 – 

Chain Saw Pivot

Operating Instructions

WP245 / WP275

3-Point Hitch Firewood Processor

28

Содержание WP245





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды