manualshive.com logo in svg

Wallenstein WP245, Руководство оператора

Поделиться
Скачать
Wallenstein WP245 Скачать руководство пользователя страница 33

5. 

Winch the log into log lead-in chute. Be careful the log does 
not catch on the front lip of the chute.

01294

Fig.  32 – 

Winching up First Log

6. 

Continue to winch up to the log stabilizer.

IMPORTANT!  Stop winching when the hook reaches the 
winch. If the operator is winching and the log is not moving, 
it is most likely because the winch is fully retracted. 
Continuing could pull the hook off the end of the rope. 

7. 

Make sure the log is stable, then disengage the winch gear. 

8. 

Move the strap to the far end of the log.

9. 

Pull out the winch rope and re-attach the winch hook.

01295

Fig.  33 – 

Reposition Winch Strap to End of Log

10. 

Engage the winch and pull the log through the log stabilizer 
up to the Log Stop Guide. 

 WARNING!

Log Stabilizer is heavy! Never attempt to push a 

log by hand through the stabilizer opening. The 

stabilizer could drop suddenly and cause serious 

injury. Always use appropriate procedure and 

tools to push or pull the log through the opening.

01306

Fig.  34 – 

Winch up to Log Stop Guide

WP245 / WP275
3-Point Hitch Firewood Processor

Operating Instructions

33

Содержание WP245





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды