Wallenstein CT16B Скачать руководство пользователя страница 40

Страница: 40 / 48

9. Troubleshooting

The following table lists problems that may be encountered, with
possible causes and suggested solutions.

If a problem persists after reading this Troubleshooting section,
contact the local dealer, distributor, or Wallenstein. Have the
machine serial number ready.

Engine related issues

Refer to the engine owner's manual found in the manual tube.

Problem

Cause

Solution

The chain is winding on the sprocket.

Too much slack in the chain

Adjust the chain length or distance between axle
sprockets.

Excessively worn sprocket. The chain and
sprocket do not match.

Replace the chain and/or sprocket with the
correct-sized part.

Unusual noises.

Excessive wear in the chain or sprocket.

Replace the chain or sprocket.

Drive belts are loose or worn.

Tighten or replace.

Excessive wear at the inside of the
chain's link plates or the teeth surfaces.

Improper centering of the sprocket.

Correct the centering of the drive and driven
sprockets.

The chain is being pushed to the side.

Remove the debris or reason the chain is being
pressed to the side.

Chain does not move.

Chain is frozen to conveyor trough or trough is
jammed with material.

Free up the chain. Clear jammed material.

Drive or idler sprocket set screws have come
loose, allowing sprocket to move from side to
side and bind.

Tighten set screws or repair sprocket as required.

Drive belt slips when conveyor starts.

Drive belt too loose.

Increase belt tension.

Belt replaced with incorrectly sized belt.

Install correctly sized belt. Refer to parts manual.

Drive belt wet.

Dry off belt.

Chain is frozen to conveyor trough or trough is
jammed with material.

Free up the chain. Clear jammed material.

Drive belt slips while conveyor is
operating.

Drive belt too loose.

Increase belt tension.

Drive pulley has oil, grease or other debris on
it.

Clean drive pulley.

Improper loading on conveyor.

Increase engine speed so conveyor speed
matches processor output.

Unusual drive belt wear.

Belt replaced with incorrectly sized belt.

Install correctly sized belt. Refer to parts manual.

Drive belt too tight.

Adjust belt to proper tension.

Engine does not start.

Chain is frozen to conveyor trough or trough is
jammed with material.

E-Stop button depressed.

Twist-turn to release.

No fuel getting to carburetor.

Add fuel to fuel tank. Refer to engine manual if
condition persists.

Troubleshooting

CT16B / CT24B

Trailer Firewood Conveyor

Содержание CT16B

















































Результаты поиска

Содержание CT16B

Отзывы:

Похожие инструкции для CT16B

Бренды по названию

Популярные бренды

Wallenstein CT16B, Руководство оператора

Результаты поиска

Содержание CT16B

Отзывы:

Похожие инструкции для CT16B

Бренды по названию

Популярные бренды