Walker T27i Скачать руководство пользователя страница 96

Страница: 96 / 100

Maintenance Instructions

T27i

Adjustments

Forward Speed Control Friction Lock

The FSC friction lock is adjusted to

hold the

selected forward speed

when the steering levers

are moved. The friction should not be so heavy as

to make

moving the FSC difficult

(too much

friction). The procedure for checking and adjusting

the FSC friction lock is as follows:

Friction

Washer

FSC

Actuator

Friction

Adjustment Nut

Forward Speed Control Friction Lock

1. Place the FSC in the full

FORWARD

position

and pull both steering levers back; the FSC

lever should not move. If the FSC lever

moves back when the steering levers are

pulled back, the

friction needs to be in-

creased.

FSC Full

Forward Position

Pull Steering Levers

Back To Check

Friction Lock

Forward Speed Control Position

(Checking Friction Lock)

2. With the steering levers held back, move the

FSC lever back from the

FORWARD

position.

With a proper amount of friction adjusted, the

FSC lever should move back with a slight

amount of resistance (friction). If the FSC

lever movement is “stiff”, the

friction needs to

be decreased.

The FSC friction is

increased

decreased

tightening

loosening

the

friction ad-

justment nut.

Loosen or tighten the nut and

check the control function until conditions of

both steps 1 and 2 (above) are met.

Содержание T27i





































































































Результаты поиска

Содержание T27i

Отзывы:

Похожие инструкции для T27i

Бренды по названию

Популярные бренды

Walker T27i, Руководство оператора

Результаты поиска

Содержание T27i

Отзывы:

Похожие инструкции для T27i

Бренды по названию

Популярные бренды