Walker T27i Скачать руководство пользователя страница 19

Страница: 19 / 100

T27i

Safety Instructions

SAFETY, CONTROL, AND INSTRUCTION DECALS

Safety, Control, and Instruction Decals are installed on the machine;

if any are missing, illegible, or damaged, a replacement should be ordered and installed before

putting the machine into operation. The Decal Part Number is listed below and in the Parts Manual.

8600-4

Location: Adjacent to Blower Discharge

Chute through Body

Part Number: 8600-4

1. Warning - rotating impeller is a cutting/dismem-

berment hazard to fingers and hands.

● Never reach down into the blower

discharge chute.

2. Warning - thrown object hazard.

● Never engage the PTO with grass catcher

raised.

Location: Engine Shroud

Part Number: 5855

8600-16

Location: Rear Cross Member of Front Body

Part Number: 8600-16

Important - Lower front body before lowering

catcher box.

Location: Rear of Grass Catcher Exhaust Screen

Part Number: 5869

Location: RH Fender

Part Number: 8600-33

1. Warning – read Operator’s Manual before

servicing or performing maintenance.

● Engage parking brake.

● Remove ignition key.

2. Forward Speed Control

● Move lever forward to increase speed; back

to stop.

Warning – do not operate the machine without

a deck or other implement attached.

4. PTO Clutch Lever

● Move lever forward to disengage PTO

clutch; back to engage.

5. Warning – do not engage PTO clutch with PTO

shaft disconnected.

Содержание T27i





































































































Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды

Walker T27i, Руководство оператора

Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды