Walker T27i Скачать руководство пользователя страница 63

Страница: 63 / 100

T27i

Maintenance Instructions

Lubrication

Mower Deck Gearbox Lubrication

NOTE:

These instructions apply to all mower

decks with gear-driven blades. Refer to

DS52

Mower Deck Lubrication on page 60

for the

DS52 deck with belt-driven blades. Refer to

Mow

er Deck Spindle Lubrication on page 60

for

mower decks with belt-driven blades.

On gear-driven decks, the mower deck gearboxes

(tee gearbox and blade drive gearboxes) are con-

nected as a unitized as sembly, and oil flows freely

between them. The gear boxes are permanently

lubricated (oil filled) and sealed requiring no sched-

uled lubrication. Howev er, the gearbox oil seals

should be checked

every 25 hours

for indication

of an oil leak;

particularly the lower seals

on the

blade drive gearboxes should be inspected, since

they operate in a dirty en vironment. If an oil leak is

noted, replace the oil seal and relubricate the

gearbox assembly as follows:

1. Remove gearbox cover (footrest). Deck orien-

tation should be the normal operating position.

Tee

Gearbox

Blade Drive

Gearboxes

Mower Deck Gearboxes

(Shown with Gearbox Cover

Removed for Clarity)

2. Clean the area around the individual gearbox

cover plates to prevent contaminants from

en tering the gearcase.

Remove the screws securing the cover plates

on the blade drive gearboxes.

4. Check the level of lubricant in the gearboxes.

If the lubricant is low, add SAE E.P. (Extreme

Pressure) 80W-90 (API GL-5) gear lube until

the oil level is up to (submerges) the horizontal

shaft in the gearbox (shaft parallel to cover

plate).

NOTE:

In case the gearboxes are completely

drained of oil, approximately 5 fl. oz. (15 cl) of

oil per gearbox is required to refill the gear

drive assembly.

NOTE:

Since the gearboxes are connected

as a unit by connector tubes, it is necessary to

add oil slowly. Allow a few minutes after add-

ing oil for the oil to flow throughout the assem-

bly and the oil level to stabilize before reas-

sembly.

IMPORTANT: DO NOT

overfill the deck gear-

boxes. The gearbox assembly is not vented,

and overfilling with oil will cause excessive

pres sure and result in oil leaks.

5. Check condition of the cover gasket and re-

place if worn or damaged. Reinstall gearbox

cover plates; torque screws to 24 lb·in. (3

N·m).

Содержание T27i





































































































Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды

Walker T27i, Руководство оператора

Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды