Walker T27i Скачать руководство пользователя страница 45

Страница: 45 / 100

T27i

Operating Instructions

Cutting height is adjusted by positioning the four

(4) re tainer hitch pins in a series of six vertical

holes on the deck support pins. Lift handles have

been pro vided on each end of the deck to assist in

raising the deck while positioning the hitch pins.

Cutting heights range from 1.5 in. (38 mm) [top

holes] to 4 in. (102 mm) [bottom holes] in 1/2 in.

(13 mm) incre ments.

Deck Support

Hitch Pin

Washer

Lift Handle

Cutting Height Adjustment

DS60-3 Cutting Height

WARNING

Never adjust cutting height while the mow-

er is moving. Before adjusting cutting

height or servicing, move the Forward

Speed Control (FSC) into the NEUTRAL-

PARK position, engage the parking brake,

and disengage the blade clutch (PTO).

Tractor should not be moving while adjust-

ing cutting height.

Cutting height is adjusted from operator’s seat

using the deck lift pedal to assist in raising the

deck while adjusting the cutting height hitch pin.

1. Disengage PTO and stop tractor.

2. Push down on deck lift pedal until it latches in

the full up (transport) position.

Select the desired cutting height by moving

the hitch pin to the location shown on the

cutting height decal.

4. Push down on the lift pedal and lift up on the

cutting height release lever. Slowly release

the pedal while lifting the lever until the deck is

in the selected cutting height position.

Height

Adjustment Decal

Deck Lift Pedal

Cutting Height

Release Lever

Hitch Pin

Cutting Height Adjustment (DS60-3)

Raise Release

Lever

Push Deck

Lift Pedal

Lowering Deck to Selected

Cutting Height (DS60-3)

DS60-3 Transport Position

1. Disengage the PTO.

2. Push down on deck lift pedal until it latches in

the full up (transport) position.

TRANSMISSION LOCKOUT

IMPORTANT:

DO NOT TOW

this mower with the

transmission lockout engaged. Towing can pro-

duce excessive internal pressure and damage the

trans mission.

To move the mower with the engine

NOT

running

(dead battery, maintenance, etc.), the hydrostatic

transmissions are unlocked (released).

1. Raise the body.

2. Lift the transmission lockout lever on both the

RH and LH transmissions and secure into

place with the locking cam.

Содержание T27i





































































































Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды

Walker T27i, Руководство оператора

Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды